23
EngLIsh
Package Contents
The package contains:
1 Cordless LED Magnetic Worklight
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the worklight:
Read instruction manual before use.
Visible radiation. Do not stare into light.
Date Code Position
The date code, which also includes
the year of manufacture, is
printed into the housing.
Example:
2016 XX XX
Year of Manufacture
Description (Fig. A)
WARNING:
Never modify the worklight or any part of it.
Damage or personal injury could result.
1
Battery pack
2
Battery release button
3
Switch
4
Pivoting head
5
Lens
6
Stand
7
Belt hook
8
Magnets
9
Bezel screws
Intended Use
Your cordless magnetic LED worklight has been designed for
professional lighting applications.
DO nOT
use under wet conditions or in the presence of
flammable liquids or gases.
This worklight is a professional tool.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm.
This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn worklight off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
WARNING:
Use only
D
e
WALT
battery packs and chargers.
nOTE:
This product contains a long-life Light Emitting Diode
(LED). This LED is not replaceable. When the LED reaches its end
of life, the worklight should be recycled or disposed of through
available channels for electrical waste and electronic equipment.
Installing and Removing the Battery Pack
(Fig. D)
nOTE:
Make sure your battery pack
1
is fully charged.
To Install the Battery Pack into the
Worklight
1. Align the battery pack
1
with the rails inside the worklight's
handle (Fig. D).
2. Slide it into the handle until the battery pack is firmly seated
in the worklight and ensure that you hear the lock snap
into place.
To Remove the Battery Pack from the Tool
1. Press the release button
2
and firmly pull the battery pack
out of the worklight's handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some
D
e
WALT
battery packs include a fuel gauge
11
which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
11
. A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE:
The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn worklight off and disconnect battery
pack before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Summary of Contents for DCL044
Page 1: ...DCL044 Final Page size A5 148mm x 210mm ...
Page 3: ...1 Fig A Fig B 2 7 6 5 3 1 8 4 9 11 Fig C 1 2 ...
Page 4: ...2 Fig F Fig D 2 1 Fig E 10 10 5 9 ...
Page 103: ...101 ...
