11
English
Utility Hook (Fig. D)
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool’s ultilty hook to hang the
tool from a work belt. DO NOT use the ultilty hook
for tethering or securing the tool to a person or
object during use. DO NOT suspend tool overhead or
suspend objects from the ultilty hook.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the ultilty hook
is secure.
iMPORTAnT:
When attaching or replacing the ultilty hook
10
,
use only the screw
14
that is provided. Be sure to securely
tighten the screw.
The ultilty hook can be be attached to either side of the tool
using only the screw provided, to accommodate left‑ or right‑
handed users. If the hook is not desired at all, it can be removed
from the tool.
Side Handle and Depth Rod (Fig. A, C)
WARNING:
To reduce the risk of personal injury,
ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle
1
clamps to the front of the gear case and may
be rotated 360˚ to permit right‑ or left‑hand use.
The side handle clamps to the collar
13
and has 12 tightening
locations. The side handle can be tightened by rotating the
grip of the side handle clockwise. The side handle must be
tightened sufficiently to resist the twisting action of the tool if
the accessory bind or stall. Be sure you moved the side handle
against the end of the collar end to have the clamping piece
fully engaged.
To Adjust the Depth Rod (Fig. A)
Loosen the side handle
1
and move the depth rod
2
so that
the distance between the end of the rod and the end of the bit
equals the desired drilling depth. When drilling with depth rod,
stop when end of rod reaches surface of material.
Electronic Overload Protection
If the drill bit becomes jammed, the power to the drill spindle
will be interrupted by the activation of the electronic overload
protection. To reactivate the power to the drive spindle, the
tool's trigger should be released and then depressed. Due to the
resulting forces, always hold the tool with both hands and take
a firm stance.
To actuate the fuel gauge, press and hold the fuel gauge
button
12
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE:
The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE:
Make sure your battery pack
8
is fully charged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
8
with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
9
and firmly pull the battery pack
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some
D
e
WALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start‑up can cause injury.
WARNING:
Use only
D
e
WALT
battery packs and chargers.
3
Trigger switch
4
Forward/reverse control button (Lock‑off button)
5
Mode selector
6
Main handle
7
Worklight
8
Battery pack
9
Battery release button
10
Utility hook
Intended Use
This heavy‑duty cordless rotary hammer is designed for
professional concrete, wood and metal drilling applications.
DO nOT
use under wet conditions or in the presence of
flammable liquids or gases.
This heavy‑duty cordless rotary hammer is a professional
power tool.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm.
This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Summary of Contents for DCH072
