background image

3

RISK OF BURSTING

RISK OF

EXPLOSION OR FIRE

AIR TANK

THE FOLLOWING CONDITIONS COULD

LEAD TO A WEAKENING OF THE TANK, AND

RESULT IN A VIOLENT TANK EXPLOSION:

1.

FAILURE TO PROPERLY DRAIN

CONDENSED

  WATER FROM THE TANK,

CAUSING RUST AND THINNING OF THE
STEEL TANK.

2. 

MODIFICATIONS

 OR ATTEMPTED

REPAIRS 

TO THE TANK.

3. UNAUTHORIZED 

MODIFICATIONS TO

THE PRESSURE SWITCH, SAFETY
VALVE, OR

 ANY 

OTHER COMPONENTS

WHICH CONTROL

 TANK 

PRESSURE.

ATTACHMENTS  & ACCESSORIES

EXCEEDING THE PRESSURE RATING OF AIR
TOOLS,

 SPRAY GUNS, AIR OPERATED

ACCESSORIES, TIRES AND OTHER
INFLATABLES 

CAN CAUSE THEM TO EX-

PLODE

 OR FLY APART, AND COULD RESULT

IN SERIOUS INJURY.

EXCESSIVE VIBRATION CAN WEAKEN THE
AIR TANK

 OF A STATIONARY COMPRESSOR

AND 

CAUSE AN EXPLOSION.

IT IS NORMAL FOR ELECTRICAL
CONTACTS

 WITHIN THE MOTOR AND PRES-

SURE SWITCH 

TO SPARK.

IF

 ELECTRICAL 

SPARKS

 FROM COMPRES-

SOR 

COME INTO CONTACT WITH

FLAMMABLE VAPORS, THEY MAY IGNITE,
CAUSING FIRE OR EXPLOSION.

RESTRICTING

 ANY OF THE 

COMPRESSOR

VENTILATION OPENINGS WILL CAUSE SERI-
OUS OVERHEATING AND COULD CAUSE
FIRE.

DRAIN TANK DAILY OR AFTER EACH USE.

IF TANK DEVELOPS A LEAK, REPLACE IT
IMMEDIATELY WITH A NEW TANK OR NEW
COMPRESSOR OUTFIT.

NEVER

 DRILL INTO, WELD, OR 

MAKE ANY

MODIFICATIONS TO THE TANK

 OR ITS

ATTACHMENTS.

THE TANK IS DESIGNED TO WITHSTAND
SPECIFIC OPERATING PRESSURES.  

NEVER

MAKE ADJUSTMENTS OR PARTS SUBSTI-
TUTIONS TO

 ALTER THE 

FACTORY SET

OPERATING 

PRESSURES.

FOR ESSENTIAL CONTROL OF AIR PRES-
SURE, YOU MUST 

INSTALL A PRESSURE

REGULATOR AND PRESSURE GAUGE TO
THE AIR OUTLET

 OF YOUR COMPRESSOR.

FOLLOW THE EQUIPMENT MANUFACTUR-
ERS RECOMMENDATION AND NEVER
EXCEED THE MAXIMUM ALLOWABLE PRES-
SURE RATING OF ATTACHMENTS.  

NEVER

USE COMPRESSOR TO INFLATE SMALL
LOW-PRESSURE OBJECTS SUCH AS
CHILDREN’S TOYS, FOOTBALLS,
BASKETBALLS. ETC.

THE 

COMPRESSOR MUST BE PROPERLY

MOUNTED

, SEE INSTALLATION PROCE-

DURES.

ALWAYS 

OPERATE THE COMPRESSOR IN A

WELL VENTILATED 

AREA FREE OF COM-

BUSTIBLE MATERIALS, GASOLINE OR
SOLVENT VAPORS.

IF SPRAYING FLAMMABLE MATERIALS,

LOCATE COMPRESSOR AT LEAST 20 FEET
AWAY FROM SPRAY AREA.

  AN ADDITIONAL

LENGTH OF HOSE MAY BE REQUIRED.

STORE FLAMMABLE MATERIALS IN A
SECURE LOCATION AWAY FROM COM-
PRESSOR.

NEVER PLACE OBJECTS AGAINST OR ON
TOP OF COMPRESSOR.  OPERATE COM-
PRESSOR

 IN AN OPEN AREA AT LEAST 

12

INCHES AWAY FROM 

ANY  WALL OR

OBSTRUCTION

 THAT WOULD RESTRICT

THE FLOW OF FRESH AIR TO THE VENTILA-
TION OPENINGS.

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

•  SAVE THESE INSTRUCTIONS •

IMPORTANT SAFETY INSTRUCTIONS

IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY
AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS
BEFORE USING THIS EQUIPMENT.

CONTINUE NEXT PAGE 

*

Summary of Contents for MG5-OLSTAT-3A

















Reviews: