background image

 

                        12

                                                                   © 2012 Finishing Brands UK Ltd.

 

 

Parts Replacement/ 
Maintenance 

 
SPRAY HEAD SEAL 
REPLACEMENT 
 

1.

 

Remove air cap and retaining ring. (See fig 37) 

2.

 

Remove fluid adjusting knob, spring, and spring pad. (See 
figs 38 & 39) 

3.

 

Remove fluid needle from gun body. (See fig 40) 

4.

 

Remove fluid nozzle using SN-28 (10 mm) ring Spanner, 
and then remove the Front Plate. (See figs 41, 42 & 43) 

5.

 

Remove Spray Head. (See fig 44). 

6.

 

Clean Spray Head with a soft brush (See fig 45). 

7.

 

Remove Spray Head seal using a small screwdriver or 
pick. (See fig 46) 

8.

 

Clean front of gun if required, using a soft brush, as well 
as the Spray Head, fluid nozzle, air cap, and retaining ring. 
(See fig 47) 

9.

 

Place a new Spray Head Seal onto the front of the gun, 
making sure the flat on the seal is aligned with the flat in 
the gun. (See fig 48). 

10.

 

Fit the Front Plate onto the Spray Head, fit Spray Head to 
the Gunbody, ensuring the flat on the underside of the 
Spray Head locates with the flat in the Gun Body. Fit Fluid 
Nozzle, Air Cap, and Retaining Ring. Torque the Fluid 
Nozzle to 18–20 nm. Don’t over torque the fluid nozzle. 
(See figs 44, 43, 42, 41 and 37) 

11.

 

Insert Fluid Needle all the way into the Gun Body, seating 
in the Fluid Nozzle. (See fig 40) 

12.

 

Reassemble Needle Spring, Spring Pad, and Fluid 
adjusting Knob. (See figs 39 & 38) 

13.

 

Trigger gun fully and screw in Fluid Adjusting Knob until it 
stops. Back it off 1/2 turn and gun will have full needle 
travel. 

14.

 

Trigger gun several times to verify correct operation

.

 

 

Summary of Contents for GFG PRO

















Reviews: