background image

 

© 2012 Finishing Brands UK Ltd.                                                          

11

 

Parts Replacement/Maintenance 

 

NEEDLE PACKING 

REPLACEMENT INSTRUCTIONS 

13. Remove trigger using key (47) or TORX (T20) 

driver. (See figs 25 & 26) 

14. Remove fluid adjusting knob and needle spring with 

spring pad from gun. (See figs 27 & 28) 

15. Remove fluid needle from gun body. (See fig 29) 

16. Loosen and remove packing nut using Key (47) or a 

straight blade screwdriver. (See figs 30 & 31) 

17. Discard old packing and packing spring if replacing. 

Clean packing if reusing. Also clean packing spring 
and nut. (See fig 32). 

18. Re-assemble the packing, (See fig 32). Assemble 

into gunbody by hand (see fig 33) and then tighten. 
(See figs 30 and 31) 

19. Insert fluid needle all the way into gun body seating 

in fluid nozzle (See fig 34).  

20. Insert needle spring, spring pad, and fluid adjusting 

knob. (See figs 28 & 27). Reinstall trigger. (See figs 
25 & 26).  

21. Trigger gun fully and screw in fluid adjusting knob 

until it stops. Back it off 1/2 turn and gun will have 
full needle travel.  

22. Trigger gun several times to verify correct 

operation. 

 

 

SPREADER VALVE ASSEMBLY 

REPLACEMENT/MAINTENANCE 

The spreader valve assembly can be replaced if 
damaged. Remove using 14mm spanner (59). (See figs 
35 & 36). The internal seal can be replaced and is 
included in the ADVANCE HD Gun Rebuild Kit. 

 
 

Summary of Contents for ADV-S430-16


















Reviews: