manualshive.com logo in svg

Devantech dS1242, User Manual

Share
Download
Devantech dS1242 User Manual Download Page 2

 

dS1242  

dS1242  

 

  

                                                   User Manual v4.10

Table of Contents

Documentation history..........................................................................................................................4

A quick look........................................................................................................................................5
Introduction........................................................................................................................................ 6

Getting started.................................................................................................................................... 7

Locating the IP Address...........................................................................................................8

Configuring the dS1242.......................................................................................................................10

Status page.........................................................................................................................11

Network page.......................................................................................................................12

Webpage security.............................................................................................................13

TCP/IP page.........................................................................................................................15
Configuring relays.................................................................................................................16

Relay automation..................................................................................................................17

Relay No. box...................................................................................................................17

Pulse/Follow box...............................................................................................................17
Set Reset & Toggle boxes...................................................................................................19

Power-up restore..............................................................................................................19

Naming I/O's........................................................................................................................20

Connecting I/O to Virtual Relays.........................................................................................20

Pinging remote machines.......................................................................................................21

Repeat Time....................................................................................................................21
Attempts.........................................................................................................................21

Delay..............................................................................................................................22
Ping Time........................................................................................................................22

Rebooting the target machine.............................................................................................22

Email notifications.................................................................................................................23

Peer to Peer.........................................................................................................................24
Sequencer...........................................................................................................................25

Sequencer commands.......................................................................................................26
K Outputs........................................................................................................................27

Sequencer Examples.........................................................................................................27

Schedules............................................................................................................................32

Counter/Timers....................................................................................................................34

The application page...........................................................................................................................37

Application page security.......................................................................................................38
Accessing your webpage from the internet................................................................................39

Boolean equations..............................................................................................................................40
TCP/IP command sets.........................................................................................................................42

ASCII command set..............................................................................................................42
Binary command set..............................................................................................................44

AES binary command set.......................................................................................................47
Modbus commands...............................................................................................................49

Function 01 (0x01) Read Coils............................................................................................49
Function 04 (0x04) Read Input Registers..............................................................................49

Function 05 (0x05) Write Single Coil....................................................................................50
Function 15 (0x0F) Write Multiple Coils................................................................................50

Error code 1.....................................................................................................................50
Error code 2.....................................................................................................................50

Error code 3.....................................................................................................................50

Loading the application firmware..........................................................................................................51

Erasing old configuration settings............................................................................................53

dS1242 Hardware...............................................................................................................................54

Copyright 

© 2016-2021,

 Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

2

Summary of Contents for dS1242
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands