manualshive.com logo in svg

Devantech dS1242, User Manual

Share
Download
Devantech dS1242 User Manual Download Page 10

 

dS1242  

dS1242  

 

  

                                                   User Manual v4.10

Configuring the dS1242

There are a set of configuration pages to get the dS1242 operating as you want it. These 

pages are all _configx.htm, (that's a leading underscore character).
ie.

_config.htm
_config2.htm

Anything that starts with _config is considered a special name for configuration pages and can 

only be seen if you have the the USB cable plugged in and connected to your PC. 

Why only if the USB cable is plugged in?
Its an additional security measure. After you have configured and deployed the module, you 

really don't want these configuration pages available for others to change. So with the USB ca-
ble disconnected the _config pages are not available. If you try to access them you just get 

served a “not authorised” page instead.

So for now, you do want to look over the config pages. If you have a Win10, Linux or MAC PC, 

you can go right ahead and plug in the USB cable. These machines will install their own USB 
drivers. We won't be sending anything to the board, its just the presence of the USB connec-

tion that enables the config pages to be served. If you have a Win7 or Win8 PC you will need 
to install the drivers. (

go to the chapter on installing the firmware and follow the instructions 

there

).

With the USB cable connected, browse to:
192.168.0.19/_config.htm

(substituting your IP address)

Copyright 

© 2016-2021,

 Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

10

Summary of Contents for dS1242
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands