background image

The ACS Series heater is a gas-fired radiant brooder. This manual provides specific information related 
to the ACS Series models. All persons involved with the installation, operation and maintenance of the 
heater system must read and understand the information in this manual.

   DANGER

WARNING

!

!

Improper installation, adjustment, alteration, service or maintenance can cause 
property damage, injury or death. Read the installation, operation and maintenance 
instructions thoroughly before installing or servicing this equipment. 

This heater 

must

 be installed and serviced by trained gas installation and service 

personnel only.  Failure to comply could result in personal injury, asphyxiation, death, 
fire or property damage. 

Do not

 store or use gasoline or other flammable vapors and liquids in the vicinity of 

this or any other appliance.

Do not use this heater in indoor living or sleeping quarters!

  Installation of a 

commercial brooder in residential indoor spaces may result in property damage, 
serious injury, asphyxiation or death.  

LIOACS-Rev. 01917

Print: LIOACS-2M-09/17_r1-01/18 (CDS)

Replaces: 

INSTALLER: Present this manual to the end user.

Keep these instructions in a clean and dry place for future reference.

Model#:

 ___________________

Serial #:

 _________________________

(located on rating label)

If you smell gas:

1.  Open windows. Do not touch electrical switches.
2. Extinguish any flame.
3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire 

department.

!

ACS Series 

Manual

Detroit Radiant Products Co. 

Installation, Operation 

Maintenance and Parts

Summary of Contents for ACS-40N-120V





































Reviews: