Detroit Diesel 60 Operator'S Manual Download Page 50 | Manualshive

Page: 50 / 172

background image

DDEC V ENGINE DRIVING TIPS

DDEC V ENGINE DRIVING TIPS

Driving with an electroncially
controlled engine feels different
from driving with a mechancially
goverened engine.

Accelerating the Vehicle

Engine response versus pedal
movement may feel different from
the mechanical-governed engine
you were driving. The Accelerator
Pedal was designed to communicate
“percentage” foot pedal travel to
the engine's Electronic Control Unit
(ECU). The engine will respond
accordingly to the driver's demand.

Another throttle or governor
characteristic you may need time to
get used to is the DDEC Limiting
Speed Governor. This allows the
driver to command total engine
response between idle and rated speed,
such as accelerating at half throttle
– an advantage when driving under
slippery conditions.

If you require wide-open throttle
engine response, either accelerating
or just plain pulling hard, the throttle
(AP) will have to be held to the floor.
To obtain 100% fueling at any speed,
the Accelerator Pedal will have to
be maintained at the fully pressed
position.

Cruise Control

For added driver convenience and
comfort, DDEC V also features a
Cruise Control option that works just
like the system in your car. It can
be operated in any gear above 1000
rpm or road speed faster than 20
mph (32 kph), up to the rated engine
speed. And it can be programmed to
hold your road speed at or below the
maximum vehicle speed. The switch
to energize Cruise Control is usually
mounted on the instrument panel.
See Figure 10.

Figure 10

Typical Cruise Control
Switches

36

All information subject to change without notice. (Rev. 01/04)

6SE484

0401

Copyright © 2004 DETROIT DIESEL CORPORATION

«
...
48
49
50
51
52
...
»

Summary of Contents for 60













































































































































































Reviews:

No comments

Related manuals for 60

Brand: Daspi Pages: 40

Brand: B&R Pages: 8

Brand: Daedong Pages: 66

24 v High Performance Synchronous Motor

Brand: Rega Pages: 1

Brand: Northern Lights Pages: 36

Brand: Northern Lights Pages: 45

Brand: Northern Lights Pages: 56

Brand: ILMOR Pages: 78

Brand: Chicago Electric Pages: 8

CYQD 32 Series CYQD32

Brand: Dongfeng Chaoyang Diesel engine Co Pages: 60

Brand: Yanmar Pages: 316

Brand: Lister Petter Pages: 60

Brand: ST Pages: 251

Brand: MVVS Pages: 12

Brand: Briggs & Stratton Pages: 17

Brand: FAAC Pages: 88

ZAtop SM180.24/B

Brand: ZIEHL-ABEGG Pages: 76

Brand: LIMBACH Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands