Detex DSI DS100-R Service & Installation Manual Download | Manualshive

Page: 13 / 27

background image

6500 Series Control Head Locking Bar Information

The 6500 Series Control Head is built to order based on a direction set up sheet sent with

cabinet on the left for waist high.

“No passage” directions include a fail lock locking bar assembly as well as an unwired solenoid.

This adds the appropriate parts to the control head to prevent it from rotating in that direction.

“Free passage” (or manual) directions remove the solenoid and locking bar assembly, allowing

the cam to spin freely.

Each direction has a pair of holes on the locking bar and control head casting. These holes

act as pivot points for the locking bar casting. The inner holes are fail lock and outer holes

are fail open. A .5“ dowel pin slides through the entire assembly to hold everything in place.

Alternate linkages and springs are needed to convert a direction’s power failure status.

any key override equipped head to ensure everything is done correctly.

Direction 1 Solenoid

Direction 2 Solenoid

Fail Open

Pivot Point

Fail Lock

Pivot Point

Fail Lock

Pivot Point

Fail Open

Pivot Point

Fail Lock

Pivot Point

Fail Open

Pivot Point

0381

Locking Bar Casting

Hardened 4140 tool steel

casting w/ oil impregnated

bronze bushings.

512-321-4426

INS-DS100R-190401

Designed Security, Inc. - 1402 Hawthorne Street, Bastrop Texas 78602 - (800) 272-3555

[email protected]

13

«
...
11
12
13
14
15
...
»

Summary of Contents for DSI DS100-R




























Reviews:

No comments

Related manuals for DSI DS100-R

SBTL7000 Series

Brand: ZKTeco Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands