5
GLOSSARY,
cont.
12
BYPASS
NOTE:
EXIT DELAY
- Time permitted to leave the premises after
arming the system. A 30 second delay is set at the factory,
but your installer can program a longer or shorter time, as
desired.
EXTENDED MONITOR
- Allows a zone to speak continu-
ously or for a programmable time period when tripped.
Example would be "pool door open, pool door open, ..."
FORCE ARM
- To override the security system's initial refusal
to arm because of an open zone. When the system is force
armed it will disregard any open zones until they have been
closed.
HOME
- Arming mode for use when you are at HOME.
Only perimeter devices are armed allowing you to move
about freely within the premises. The system will be
programmed to eliminate all entrance delays when armed to
home. This might be preferable for individuals living alone.
INTERIOR ZONES
- Zones consisting of motion detectors or
any other detection devices located within the premises.
LED
- Light emitting diode. These are used as indicators of
system conditions on keypads.
NIGHT
- Arming mode for use when everyone is in for the
NIGHT. All perimeter devices become instant and some
interior zones can be active.
PERIMETER ZONES
- Zones consisting of door and window
contacts and glass break detectors which will detect an
intruder before he gains entry into the premises.
PREALARM SPEECH
- When the system is armed, and
someone enters the premises through a "delay" door, the
system speaks "entry detected" followed by the word
description programmed for that door. Example: "entry
detected, front door...entry detected, front door." This speech
will be heard for the duration of the entrance delay. If the
disarm code is not entered within the programmed time, the
BURGLAR ALARM will sound. If an alarm took place while
you were gone, then the system would speak "system
showing alert," followed by the prealarm speech.
PREALARM TONE
- Steady, low volume sound emitted
through the speakers when the entry delay door is opened.
This tone will continue until the disarm code is entered to
disarm the system. If the disarm code is not entered within
the programmed time, the BURGLAR ALARM will sound. A
pulsing prealarm tone indicates there was an activation while
you were gone.
ZONE
- Any area or point of protection in the security system
such as doors, windows, and all other areas covered by
detection devices.
EXIT DELAY
FORCE ARM
HOME
INTERIOR ZONES
LCD
LED
NIGHT
PERIMETER ZONES
PREALARM SPEECH
PREALARM TONE
ZONE
Assuming your primary code is
1,2,3,4
:
1. Enter
1, 2, 3, 4, 7.
2. The system will speak ENTER USER NUMBER.
3. Enter 2 digit user number, (
01
-
08
). The system will
speak "ENTER CODE
X X
" (
X X
=
01
-
08
). You do
not need to clear a code to change a code.
4. Enter the new 4 digit code
or
hit the
A
key to delete
the user code from step 3. If a new 4 digit code is
entered the system will speak EXIT after the 4th
digit. If a code is deleted the system will speak
CODE OUT.
BYPASS
CHANGING/DELETING USER CODES
To enter BYPASS mode, your system must be disarmed. Make
sure the system is disarmed and follow the steps below:
1. Enter your code and immediately press the
9
key to
gain entry into BYPASS mode. You will hear BYPASSED
MODE, ENTER ZONE NUMBER.
2. Enter the two digit number of the zone (use a leading zero if
necessary) you wish to bypass. You will hear (description of
selected zone) BYPASSED (ON or OFF). Only zones that
exist in the system can be bypassed. If an invalid zone
number is entered, refusal will be signaled by three beeps.
3. Press the
*
or
A
key. The yellow STATUS LED will light to
indicate that the zone is bypassed. A second push of the
*
or
A
key within 10 seconds will remove the zone from bypass
and the yellow STATUS LED will clear.
4. Pressing
00
while in BYPASS mode will clear all bypassed
zones.
5. Press the
#
or
H
key to exit BYPASS mode. You will hear
EXIT.
NOTE:
If ten seconds pass without pressing any keys, the system
will automatically exit BYPASS mode.
EXT. MONITOR
