26
49-1000361 Rev. 3
Installation Instructions
STEP 12 START ICEMAKER
CAUTION
To minimize the risk of personal
injury, avoid contact with the moving parts of the
ejector mechanism, or with the heating element that
releases the cubes. Do not place fingers or hands
on the automatic ice making mechanism while the
appliance is plugged in.v
• Set the ice maker to
ON
with the control panel.
• The icemaker will begin operation automatically.
• Be sure nothing interferes with the sweep of the
feeler arm.
• Discard the first full bucket of ice cubes.
• Use the control panel to set the ice maker to
OFF
.
STEP 11 CONNECT POWER,
CLOSE GRILLE PANEL
• Open the grille panel.
• Plug in the power cord (if necessary) by reaching
into the opening next to the water filter. The water
filter guard will need to be removed for access
(some models). Remove the 3 screws holding it in
place. If access is still too tight, remove the 2 screws
holding the water filter bracket and move aside. Plug
in the power cord. Secure the bracket and guard
with the original screws.
• Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights are
on.
• The temperature controls are preset at 37°F (3º C)
for the refrigerator section and 0°F (-18º C) for the
freezer.
• Allow 24 hours to stabilize before making
adjustments.
STEP 10 CONNECT WATER
SUPPLY
• Locate and bring the
tubing to the front of
the cabinet.
• Turn the water on
to flush debris from
the line. Run about
a quart of water
through the tubing
into a bucket, then
shut off the water.
Copper Tubing:
6OLSD´QXWDQGIHUUXOHSURYLGHGRYHUERWKHQGV
of the copper tubing. Insert the tube into the union
fitting on the unit and tighten the nut to the union.
• Turn on the water to check for leaks.
SmartConnect
™
Tubing:
NOTE:
The only Café-approved plastic tubing is
supplied in the SmartConnect
™
Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Other
types of plastic may crack or rupture with age and
cause water damage to your home.
SmartConnect
™
5HIULJHUDWRU7XELQJ.LWVDUHDYDLODEOH
in the following lengths:
2’ (.6 m) WX08X10002
8’ (2.4 m) WX08X10006
15’ (4.6 m) WX08X10015
25’ (7.6 m) WX08X10025
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression nut
until it is just hand tight.
• Tighten one additional turn with a wrench.
2YHUWLJKWHQLQJFDQFDXVHOHDNV
• Turn on the water to check for leaks.
• Run dispenser, if available, for 2 minutes or 1 gallon
of water. It is normal for the dispenser to sputter for
the first few cups
NOTE:
Make sure excess tubing length does not
interfere with the toekick installation.
Water Filter
Guard in Front of
Electric Outlet
Access
Bracket
Screws
Screws
Refrigerator
Water Supply
House
Water Supply
INST
ALLA
TION INSTRUCTIONS
WARNING
Connect to potable water supply
only. A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 psi (275-827 kilopascals).
WARNING
ELECTRIC SHOCK HAZARD
Attach tubing clamp using existing hole only. DO
NOT drill into the refrigerator.
Summary of Contents for CAFE CSB42
Page 1: ...Owner s Manual ...
Page 33: ...32 49 1000361 Rev 3 Notes ...
Page 69: ...32 49 1000361 Rev 3 Notes ...
Page 105: ...32 49 1000361 Rev 3 Notas ...
