background image

DRAWING FOR STEP 1

STEP 12 

INSTALL TWO ROD GUIDES

            1.Take the approximately middle of upper and

                lower connecting tube.

            2.Tighten screws to install rod guides.

STEP 11 

TEST ACTUATING BAR AND 

                   DOGGING OPERATION

            1.The top latch assembly should engage the top

               strike and the bottom latch assembly should

               engage the floor strike when the door is closed.

               If the door can be pushed open without 

               depressing the actuating bar, the upper 

               connecting tube has been over adjusted. 

               Readjust it as needed.

            2.The top and bottom latch assembly should

               disengage from the strikes freely when

               the actuating bar is depressed or dogged

               down. If they do not disengage, adjust the

               bolt in the bottom latch assembly as needed and 

               retest for proper operation.

STEP 10

INSTALL FLOOR STRIKE

            1.Let the bolt in the lower bottom latch assembly

               touch the floor and mark on floor.

            2.Drill a 5/8” dia, 1” deep hole.

            3.Let the bolt in the lower bottom latch assembly

               insert into the center hole of floor strike and 

               mark 3 anchor / screw holes on floor.

            4.Drill 3 anchor / screw holes, 1/4" dia , 1 1/8" deep.

            5.Hammer 3 anchors into 3 anchor / screw holes.

               Tighten up 3 screws.

           

STEP 13 : INSTALL 4 COVERS

                Install head cover, end cover, top latch

                cover,bottom latch cover and tighten screws.

STEP 8 

INSTALL AND ADJUST UPPER

                CONNECTING TUBE

           1.Keep the end of the tube with the threaded

              insert upward to connect it with the threaded

              bolt in the top latch  assembly

           2.Connect the other end of the tube to the

              internal mechanism of the head assembly

              by inserting the connecting pin into the 

              holes.

           3.Turn and adjust upper connecting tube

              until top latch assembly retracts properly 

              and then fix the connecting pin by bending 

              2 ends.

STEP 9 

INSTALL AND ADJUST LOWER

                 CONNECTING TUBE

           1.Keep the end of the tube with the threaded

              insert downward to connect it with the 

              threaded bolt in the bottom latch assembly

           2.Connect the other end of the tube to the 

              internal mechanism of the head assembly 

              by inserting the connecting pin into the holes.

           3.Connect bolt in bottom latch assembly with 

              lower connecting tube.

              Then, depress actuating bar and adjust lower 

              connecting tube until bottom latch assembly

              retracts properly.

              Then, fix the connecting pin by bending 2 

              ends. Do not let bolt in bottom latch assembly 

              touch floor while depressing actuating bar.

Summary of Contents for F2000V Series








Reviews: