manualshive.com logo in svg

Desert Aire CM35xx, Quick Start Manual, Page: 11 / 12

Share
Download
Desert Aire CM35xx Quick Start Manual Download Page 11

11

 

 

low pressure trip is varied based upon the glycol ratio.

 3.12 

Sensor 

Offsets

 

 

This screen allows the control values of the analog input points to be adjusted if 

 

 

calibration shows these devices to be inaccurate.  The range of these offsets that can 

 

 

be entered is from -99.9 to 99.9. Care must be used when applying an offset to an 

 

 

analog value as erratic operation can result. To modify the offsets, press the ENTER 

 

 

key until the desired offset is selected and use the arrow keys until the desired setting 

 

 

is shown. Pressing the ENTER key will now change the offset.

 3.13 

Building 

Management 

Communication

 

 

The Building Management Communications is set to correspond with the serial card 

 

 

installed in the controller.  The communication types available with a CM35xx controller 

 

 

are LONWORKS®, BACnet™ MSTP, BACnet™ EtherNET or ModBus® Slave.  The 

 

 

correct serial card must be installed in the controller for the BMS communications to 

 

 

be active. In the ModBus® Slave mode, the baud rate and address will be displayed. 

 

 

The baud rate can be set to 1200, 2400, 4800, 9600 or 19200. The address should be 

 

 

set to the node number for the dehumidifi er on the ModBus® network.

4. Alarm 

Menu

 

The ALARM MENU can be accessed anytime by pressing the ALARM key.  The main Alarm 

 

Screen includes the instructions for viewing and resetting the alarms, as well as a means to 

 

access the Alarm History Screen.  Pressing the ENTER key while viewing the main Alarm 

 

Screen will reset any alarm that has returned to its safe state. Please note that active alarms 

 

can only be reset on this screen and not while the alarm is being displayed. Return to this 

 

screen and press the ENTER key to reset any alarm that has returned to its safe state. Any 

 

active alarm can be viewed by pressing the DOWN key from this screen. If no alarm screen is 

 

shown, no alarms are active. To view the Alarm History Screen, press the ALARM key.

 4.1 

Alarm 

History 

Screen

 

 

The Alarm History Screen is accessible from the main Alarm Screen by pressing the 

 

 

ALARM key. This screen lists a history of alarm conditions by time and date which 

 

 

have existed on the unit. The most recent alarm will be displayed as 001. The 

 

 

condition that triggered the alarm will be displayed along with the sensor data saved 

 

 

at the time the alarm was triggered. This is done to aid in troubleshooting the alarm 

 

 

condition. To access the entire listing of the alarm history, use the DOWN key to scroll 

 

 

through the recorded alarms.

 

Desert Aire - CM35xx Quick Start Guide

Summary of Contents for CM35xx













Reviews:

No comments