background image

www.desatech.com

111099-01C

5

Note:

 For outdoor installations, the fireplace en-

closure must allow for adequate drainage and fresh 

air ventilation. It is recommended that a sealed, 

corrosion resistant catch pan with provision for 

drainage be installed under the fireplace within 

the fireplace enclosure.

HEARTH EXTENSION

A hearth extension projecting a minimum of 16" 

in front of and a minimum of 8" beyond each 

side of the fireplace opening is required to protect 

combustible floor construction in front of the fire-

place. Fabricate a hearth extension using a material 

which meets the following specifications: a layer 

of noncombustible, inorganic material having a 

thermal conductivity of K=0.84 BTU IN/FT, HR. 

F (or less) at 1" thick. For example, if the material 

selected has a K factor of 0.25, such as glass fiber, 

the following formula would apply:
 

0.25 x 1.0" = 0.30" thickness required

 

0.84

Thermal  conductivity  "K"  of  materials  can  be 

obtained from the manufacturer or supplier of the 

noncombustible material. If the hearth extension 

is to be covered, use noncombustible material such 

as tile, slate, brick, concrete, metal, glass, marble, 

stone, etc. Provide a means to prevent the hearth 

extension from shifting and seal gap between the 

fireplace frame and hearth extension with a non-

combustible material (see Figure 3). 

 WARNING: Hearth extension 

is to be installed only as shown 

in Figure 3.

FIREPLACE INSTALLATION

Continued

Figure 3 - Hearth Extension

Seal Gap

Fireplace Front

Ember Protector

Fireplace Front 
Raised Hearth

Fireplace Front 
Elevated

Ember Protector

Ember Protector

Seal Gap

Hearth 

Extension

MANTELS

A mantel may be installed if desired (see Figure 

4). Woodwork such as wood trims, mantels or 

any other combustible material projecting from 

the front face must not be placed within 12" of 

the  fireplace  opening.  Combustible  materials 

above 12" and projecting more than 1 

1

/

2

" from 

the fireplace must not be placed less than 15" 

from the top opening of the fireplace (NFPA STD 

211, Sec. 7-3.3.3).
Mantels or any other combustible material also 

may come up to the side edge of the black metal 

face of the fireplace just as long as the projection 

from the front face fall within the limit shown in 

Figure 4.

12 

1

/

4

" Ref.

6"

Ref.

15" Min.

12" Min.

1

1

/

2

" Max.

3" Nom.

33°

Combustible 
Material

Safe 
Zone for 
Projection of 
Combustible 
Materials

Fireplace 
Opening

Upper 

Section of 

Fireplace

Figure 4 - Mantel Clearances to 

Combustible Material

FIREBOX

SAFE ZONE

Top View of Fireplace

2" Max.

3.0"

Min. to 

Perpendicular 

Side Wall 

12"

8.0"

33°

Combustible 
Material Must 
Not Overlap 
Front Face

Summary of Contents for VS42 Series





















Reviews: