background image

17

901847

OWNER’S MANUAL

ACCESSORIES

Purchase these fireplace accessories from
your local dealer. If they can not supply
these accessories, call DESA International’s
Sales Department at 1-800-432-2382 for
information. You can also write to the ad-
dress listed on the back page of this manual.

EQUIPMENT SHUTOFF
VALVE GA5010

For all models. Equipment shutoff valve with
1/8" NPT tap. Fits 1/2" NPT pipe.

RECEIVER AND HAND-
HELD REMOTE CONTROL
KIT - GHRC Series

For all models. Allows the gas log set to be
turned on and off by using a hand-held
remote control. Valve/Pilot Kit GA9103
must be used with this remote.

ON/OFF SAFETY VALVE/
PILOT KIT - GA9003

(Not Shown)

For all models. Required for Propane/LP
installation.

REMOTE READY VALVE/
PILOT KIT - GA9103

(Not Shown)

For all models.

CLEANING AND
MAINTENANCE

• Keep the area around the log set clean

and clear of debris.

• Occasionally, you may use a soft bristle

brush to clean logs.

• Once every year a qualified agency or

certified chimney sweep should exam-
ine and clean the venting system of the
fireplace.

REPLACEMENT
PARTS

Note:

 Use only original replacement parts.

This will protect your warranty coverage for
parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA International’s Technical Service
Department at 1-800-DESA LOG (1-800-
337-2564).

When calling DESA International, have ready

your name

your address

model and serial numbers of your fireplace

how fireplace was malfunctioning

type of gas used (propane/LP or natural
gas)

purchase date

Usually, we will ask you to return the defec-
tive part to the factory.

PARTS NOT UNDER
WARRANTY

Contact authorized dealers of this product
or Parts Central (see page 20). If they can’t
supply original replacement part(s), call
DESA International’s Parts Department at
1-800-972-7879 for referral information.

When calling DESA International, have ready

model number of your fireplace

the replacement part number

PINE CONES - GA9600

(Not Shown)

For all models. Use for additional decora-
tion only. Carton of 6 Boxes (3 pine cones
per box).

ASH BED MATERIAL
(Vermiculite) - GA9700

(Not Shown)

For all models. Carton of 6.

GLOWING EMBERS - GA9900

(Not Shown)

For all models. Use for firebox decoration
only.

SILICA SAND - GA9800

(Not Shown)

For all models. Use for firebox decoration
only. Carton of 6.

LAVA ROCK - GA6066

(Not Shown)

For all models. Use for firebox decoration
only.

DECORATIVE ASH BED
CONTROL COVER - DABK

(Not Shown)

An attractive way to cover control knob
and piezo ignitor.

18" ORNAMENTAL GRATE
ENHANCER - GA9310

(Not Shown)

For 18" models only. Additional decoration
for front grate.

24" ORNAMENTAL GRATE
ENHANCER - GA9320

(Not Shown)

For 24" models only. Additional decoration
for front grate.

Summary of Contents for Vanguard VVTR18























Reviews: