background image

LIMITED WARRANTY

VENT-FREE GAS BAY FRONT FIREPLACE

DESA Heating Products warrants this product to be free from defects in materials and components for two (2) 

years from the date of first purchase, provided that the product has been properly installed, operated and maintained 

in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled 

check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required 

to restore this fireplace to proper operating condition and an allowance for labor when provided by a DESA 

Heating Products Authorized Service Center. Warranty part(s) MUST be obtained through authorized dealers of 

this product and/or DESA Heating Products who will provide original factory replacement parts. Failure to use 

original factory replacement parts voids this warranty. The fireplace MUST be installed by a qualified installer in 

accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts 

that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by 

improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to 

repairing a defective fireplace will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE 

OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED 

WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUD

-

ING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO 

(2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA HEATING 

PRODUCTS’ LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND 

DESA HEATING PRODUCTS SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER 

INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of 

incidental or consequential damages, so the above limitation on implied warranties or exclusion or limitation on 

damages may not apply to you.

This warranty gives you specific legal rights and you may also have other rights that vary from state to state.
For information about this warranty write:

701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 410-9004
www.desatech.com

113896-01
Rev. D
05/06

NOT A UPC

WARRANTY INFORMATION

kEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our 

standard written warranty. We make no other warranty, expressed or implied.

113896 01

f i r e - p a r t s . c o m

Summary of Contents for Comfort Glow CF26NTA

































Reviews: