manualshive.com logo in svg

Desa CLD3924NTC, Owner'S Operation And Instruction Manual, Page: 25 / 32

Share
Download
Desa CLD3924NTC Owner'S Operation And Instruction Manual Download Page 25

www.desatech.com

120890-01D

25

Glass Doors

Figure 31 - Installing Thermostat Sensing 

Bulb behind Glass Doors

Thermostat 
Sensing Bulb

Adhesive-
backed 
Mounting Clip

4.  Mounting clip must be a minimum of 3" 

from bottom of fireplace to prevent crimp

-

ing of capillary. Once you have decided 

on  a  location,  clean  area  thoroughly. 

Remove paper backing from adhesive on 

back of mounting clip. Press clip into new 
location so thermostat sensing bulb will 
be  positioned  vertically  with  capillary  at 

bottom (see Figure 32). Slide thermostat 
sensing bulb into clip.

 

IMPORTANT:

 Do not crimp capillary.

OPTIONAL POSITIONING OF THERMOSTAT 

SENSING BULB

Continued 

Capillary

Thermostat 
Sensing Bulb

Do Not Crimp 
Capillary

Adhesive-
backed 
Mounting Clip 

Figure 32 - Positioning Thermostat 

Sensing Bulb in Vertical Position with 

Capillary at Bottom

SPEcIFIcATIONS

Model CLD3924PTC

•  Rating (Variable): 20,000/39,000 Btu/Hr
•  Type Gas: Propane/LP
•  Ignition: Piezo
•  Pressure Manifold: 8.0" W.C.
•  Inlet Gas Pressure (in. of water):
  Maximum 14" W.C., Minimum* 11" W.C.
•  Shipping Weight: 

27 lbs.

* For input adjustment

Model CLD3924NTC

•  Rating (Variable): 20,000/39,000 Btu/Hr
•  Type Gas : Natural Gas
•  Ignition: Piezo
•  Pressure Manifold: 3.5" W.C.
•  Inlet Gas Pressure (in. of water):
  Maximum 10.5" W.C., Minimum* 5" W.C.
•  Shipping Weight: 

29 lbs.

* For input adjustment

Summary of Contents for CLD3924NTC

































Reviews:

No comments