background image

11

102667

INSTALLING

Continued

INSTALLATION CLEARANCES

Note: Clearances
are the same if
using optional
cabinet mantel or
built-in installation.

WARNING ICON

G 001

 WARNING

Maintain the minimum clearances. If you can, provide greater
clearances from floor, ceiling, and adjoining wall.

Continued

Carefully follow the instructions below. This will ensure safe installation.

Minimum Wall and Ceiling Clearances (see Figure 7)

A. Clearances from the side of the fireplace opening to any combustible wall should

not be less than 16 inches for a cabinet mantel or 12 inches for a corner installation.

B. Clearances from the top of the fireplace opening to the ceiling should not be

less than 42 inches.

Note:

 

The instructions below show installation using the cabinet mantel and the

G3000F/G3001U hearth base accessories. The hearth base accessory shown is
optional for this installation. You can install fireplace and cabinet mantel directly
on the floor. The corner mantel and face mantel accessories cannot be installed
with the G3000F/G3001U hearth base. You must install corner and face mantel
directly on the floor. If mounting fireplace and cabinet mantel to the floor or using
face mantel or corner mantel, an optional G3005 Slim Base kit may be installed.

1. Assemble cabinet mantel, hearth base, and trim accessories. Assembly instruc-

tions are included with each accessory.

2. Install a properly grounded, 120 volt three-prong electrical outlet at fireplace

location if an outlet is not there. If possible, locate outlet so cabinet mantel
will cover it when installed (see Figure 8, page 12).

WARNING ICON

G 001

 WARNING

For conventional installation, it is recommended you use the
cabinet mantel, corner mantel, face mantel, or hearth bases speci-
fied in this manual. Surface clearances may not be sufficient with
other cabinet mantels and hearth bases. This may create a fire
hazard. See 

Accessories, pages 32 and 33 for correct mantels and

hearth bases.

CONVENTIONAL FIREPLACE INSTALLATION

Conventional installation of this fireplace involves installing fireplace along with the
corner, face, or cabinet mantel with hearth base accessories against a wall in your
home. Follow the instructions below to install the fireplace in this manner.

Figure 7 - Minimum Clearance to Wall and Ceiling

,,,,,

,,,,,

,,,,,

,,,,,

,,,,,

QQQQQ

QQQQQ

QQQQQ

QQQQQ

QQQQQ

¢¢¢¢¢

¢¢¢¢¢

¢¢¢¢¢

¢¢¢¢¢

¢¢¢¢¢

42"

16"

Face or

Cabinet  

Mantel  

Corner

Mantel

12"

MINIMUM CLEARANCE
Side Wall - 16 " Cabinet and

Face Mantel

Ceiling - 42" Corner Mantel
Floor - 0"

Summary of Contents for CFGF28PTA













































Reviews: