Denver CR-26 DABPLUS Instruction Manual Download Page 9

Page: 9 / 27

UK-3

To check the alarm status, during FM operation, press the

INFO

button; and in DAB operation, repeatedly

press the

INFO

button until the display shows the alarm status.

Note :

The alarm comes first will have the priority and it would continue for a one hour duration, the snooze will

just switch off this alarm temporary during this duration, so if the second alarm comes in this period, it will
not function. But if the first alarm is switched off before the second alarm arrives, then the second alarm
will be activated.

SNOOZE FUNCTION

During alarm, press the

SNOOZE

button will temporary switch off the alarm for 5 minutes and the snooze icon “

z “ will be displayed. This is repeatable in the one hour alarm duration. (F.11)

SLEEP FUNCTION

This  function  allows  you  to  program  the  radio  to  switch  off  itself  after  a  set  period  of  time.  You  can  set  your
sleep  time  in  either  standby  or  on  mode;  if  the  sleep  time  is  set  in  standby,  the  radio  will  switch  to  on
automatically after the setting is confirmed.
1.   To activate the sleep function, press the

SLEEP

button, “Sleep 90 min” will appear in the display.

Repeatedly press the

SLEEP

button, the time in the display will change in sequence on every press:

When your desired sleep time appears in the display, release the button and the sleep timer is activated.
The “second” digits of the clock will change to display “S#” where “S1” is to represent “10 minutes” sleep
time and so on. (F.12)

When the sleep timer counts to zero, the unit will go off.

To put the sleep function off during sleep timer on, press the

SLEEP

button once, the display will show

“Sleep OFF” and the “S#” will change back to show the “second”.

LISTENING TO YOUR RADIO

Hints for better reception

This radio carries a single DAB/FM lead wire antenna, to obtain the best performance, you should fully extend
the wire antenna and adjust the position as well as the direction until you find the best reception. For ideal DAB
reception, always maintain the lead wire antenna in a vertical position (holding it upward or downward behind
the unit) is highly recommended.

DAB mode

When the radio is first powered up and switched on from standby, DAB mode will be automatically selected and
it will perform services full scan function. During the scan, the display will show a slide bar that indicates the
progress of the scan. After the scan has finished, the number of services found will be displayed and then the
first alphanumerically found station will be automatically selected.
DAB-unlike normal radio-groups together several radio stations and transmits them on one frequency. These
groups are referred to as multiplexes and ensembles. Every time one of these groups has been found, the
name of that group will be displayed.

Auto services scan modes

There  are  two  types  of  services  scan  modes,  one  is  quick  scan  and  the  other  is  full
scan.  Quick  scan  will  only  search  for  the  middle  part  of  the  DAB  Band  III  channels
and  full  scan  will  search  for  the  entire  DAB  Band  III  channels.  Once  the  scan  has
finished, the radio will select the first alphanumerically found station.
1.      To activate the quick scan, press the

AUTOTUNE

button once, the display will

show “Scan Services Quick Scan“ and then a progressing slide bar. (F.13)

2. To activate full scan, press and hold the

AUTOTUNE

button until the display

shows “Scan Services Full Scan”. (F.14)

To explore the stations those have been found, press the

SELECT

button once

and when the display shows “< SELECT >”, rotate the

SELECT CONTROL

for

stations.

Manual tuning

1. To select manual tuning, press and hold the

INFO

button until the display shows “Manual Tune”, then

press the

SELECT

button to confirm.

Rotate the

SELECT CONTROL

to move through the DAB channels, the display will show “5A to 13F” and

their associated frequencies. When your radio locates a station group (ensemble/multiplex) on one of the
DAB channels, the name of the station group will appear on the bottom of the display.

To select the ensemble/multiplex, press the

SELECT

button, the display will show the first station in the

ensemble/multiplex.

Rotate the

SELECT CONTROL

to explore the stations existed in the ensemble/multiplex, when you have

located your desired station, press the

SELECT

button, and at the same time, you will also exit from the

manual tuning mode.

F12