Dension WiRC User Manual Download Page 2

Disclaimer 

Please read and fully understand this manual before installing and operating 
WiRC. 

Everyone should use WiRC on their own responsibility.

 

Children under 12 years should use WiRC with adult supervision. 

 

Improper use of models may cause injuries or property damage, so please 
always drive with extreme caution. Never use models on public roads, crowded 

areas, near small children or animals.  

 

Take extreme care when connecting electrical components. Do not use cables 
with damaged connectors or insulation and take care of correct polarity.  
Incorrect electrical connections may cause short circuit or even fire. 
Models have moving and rotating parts and some components may get hot 
after use. To avoid injuries, do not touch these parts! 

 

Incorrect setup of failsafe functions and too low battery voltage may cause the 
loss of control on model, and may cause damages. 
Read and understand the manual of other components (incl. batteries, 
chargers, etc) connected to WiRC. Use only such components that fit the WiRC 
technical specifications. 

 

Other WiFi networks or strong electromagnetic fields may affect the 
performance of WiRC! By using WiRC consider applicable local regulations on 

personality rights and data protection laws. 

 

WiRC has 12 month full warranty, which covers defects caused by 
defective parts or workmanship. 

Warranty does not cover defects, damages or injuries due to improper 
installation, regardless use of WiRC driven models, or any problems caused by 
other parts in model. 

 

Dension reserves right to change the product, it's components or contents of 
this manual, without any prior notice! 

Summary of Contents for WiRC

























Reviews: