3
Introduction
Introduction
ENGLISH
ENGLISH
●
Before turning the power switch on
Check once again that all connections are correct and that there
are no problems with the connection cables.
●
Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for
long periods of time, be sure to unplug the power cord from the
power outlet.
●
Sufficiently ventilate the place of installation
If the unit is left in a room full of the smoke from cigarettes, etc., for
long periods of time, the surface of the optical pickup could get
dirty, in which case it will not be able to read the signals properly.
●
About condensation
If there is a major difference in temperature between the inside
of the unit and the surroundings, condensation (dew) may form
on the operating parts inside the unit, causing the unit not to
operate properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
●
Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so,
move the mobile phone away from this unit when it is in use.
●
Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units
before moving the unit.
●
Note that the illustrations in these instructions may differ from
the actual unit for explanation purposes.
Moisture condensation may occur inside the unit when it is
moved from a cold place to a warm place, or after heating a cold
room or under conditions of high humidity. Do not use the unit at
least for 2 hours until its inside is dry.
• Do not handle the AC cord with wet hands.
• Do not pull on the AC cord when disconnecting it from AC wall
outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the AC cord
immediately and take the unit to our authorised service centre
for servicing.
Pay attention to the following before using this unit:
●
Moving the unit.
To prevent short-circuits or damaged wires in the connection
cables, always unplug the power supply cord and disconnect the
connection cables between all other audio components when
moving the unit.
●
Store the operating instructions in a safe place.
After reading the operating instructions, store them in a safe
place as they could come in handy in the future.
●
Whenever <ON/STANDBY> is in the STANDBY state, the unit
is still connected to AC line voltage.
Please be sure to unplug the cord when you leave home for, say,
a vacation.
●
Note that the illustrations in these instructions may differ
from the actual unit for explanation purposes.
The serial number of this product may be found on the back of
the unit. No others have the same serial number as yours. You
should record the number and other vital information here and
retain this book as a permanent record of your purchase to aid
identification in case of theft.
Cautions on Handling
DVD-2500BT
BLU-RAY DISC PLAYER
HDMI
RESOLUTION
SD CARD
ON / STANDBY
10 cm or more
Wall
Dew Warning
Avoid the Hazards of Electrical Shock and Fire
Before Using
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Supplied Accessories
Please check to make sure the following items are included with
the main unit in the carton.
remote control (RC-1091)
“R6P” (AA) batteries x2
AC cord
operating instructions
service station list
Trademark Information
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC.
Manufactured under license from Dolby Laboratories. Dolby and
the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and
worldwide patents issued & pending. “DTS” and “DTS Digital
Surround” are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All
Rights Reserved.
E5J01_03_05ED_EN.book Page 3 Tuesday, November 11, 2008 11:38 AM
