11
3. DEVICE OPERATION
• When the button is held pressed for more than 1 second, playback is in FF or FR of 2
times speed. (with audio output)
• When the button is held pressed for more than 4 seconds, playback is in FF or FR of 10
times speed. (with audio output)
• When the button is held pressed for more than 7 seconds, playback is in FF or FR of 100
times speed. (without audio output)
• When the button is held pressed for more than 10 seconds, playback is in FF or FR of 200
times speed. (without audio output)
• At the end of the final track, the playback is in pause mode.
7. Manual search in reverse
DN-F400: Press the
4
button.
RC-F400S: Press the
1
button.
• Every time the
1
button is pressed, the playback point retreats one file.
• When the button is held pressed for more than 1 second, playback is in FF or FR of 2
times speed. (with audio output)
• When the button is held pressed for more than 4 seconds, playback is in FF or FR of 10
times speed. (with audio output)
• When the button is held pressed for more than 7 seconds, playback is in FF or FR of 100
times speed. (without audio output)
• When the button is held pressed for more than 10 seconds, playback is in FF or FR of 200
times speed. (without audio output)
• At the beginning of the track, the playback point moves to the end of the previous track
and playback starts in FR.
At the beginning of the first track, playback is in pause mode.
Note:
• If a track with short length is manually searched for at high speed, the intended speed may
not be achieved. With this unit, n-time-speed search is achieved by repeated playback for
a duration of 0.5 seconds at the intervals of n-time-speed searching.
8. Finishing manual search
DN-F400: Release the
4
or
¢
button.
RC-F400S: Release the
1
or
¡
button.
• If manual search is started during stop or pause, the searched point is reproduced
repeatedly after manual search is finished.
• If manual search is started during playback, after manual search is finished, playback
restarts from the point where the button is released.
• During 0.2 second after hot-start playback is started, no command, including searching,
can be accepted.
9. Frame jump
While a searched point is reproduced repeatedly in Step 8, if the
1
or
¡
button of the
RC-F400S is pressed then released within 1 second, a reproduced point will jump by one
frame.
ADVANCED PLAYBACK
Setting of the MODE switch
OFF
ON
Various playback modes shown in the table below are available by setting the MODE switch on
the rear panel of the DN-F400.
Note:
• Be sure to turn the power off before setting.
Switch No.
Items
Setting
Default setting
1
POWER ON
PLAY
ON :
Playback starts automatically when the
power is turned on.
OFF : Playback does not start automatically when
the power is turned on.
OFF
2
PLAY MODE
ON :
SINGLE mode (When playback ends, it stops.)
OFF : CONT. mode (When playback ends, the
next track is played back.)
OFF
3
REPEAT
ON :
Repeat playback
OFF : No repeat playback
OFF
4
RANDOM
ON :
Random playback
OFF : No random playback
* enabled when SW2 (PLAY MODE) is set to OFF
OFF
5
FINISH MODE
ON :
RECUE mode (When playback ends, the
playback point moves to the playback
starting point, and the unit enters CUE
mode.)
OFF : NEXT mode (When playback ends, the playback
point moves to the beginning of the next track
and the unit enters the CUE mode.)
* enabled when SW2 (PLAY MODE) is set to OFF
OFF
6
PARALLEL
Setting of the parallel remote connector
ON :
Hot-start mode
OFF : Normal mode
OFF
7, 8
RESERVE
For system setup. Never change the settings.
OFF
