5
Rear Panel
1.
Power Input:
Use the included power cable to connect this input to a power outlet.
2.
Line Outputs:
Use Euroblock connectors to connect these line-level outputs to your
loudspeakers or other audio devices.
Each group of 5 connections corresponds to 2 zones.
Each zone has a hot (
H
) and cold (
C
) connector, and each pair of zones shares the ground (
G
)
connector. Make sure each loudspeaker is connected to the desired zone.
To send audio signal to the
Speaker Outputs
, use the included
5-pin Euroblock with jumper wires
to connect the
Line Outputs
of Zones 1-4 to the
Amp Inputs
of Zones 1-4.
3.
Mic
/
Line Inputs:
Use Euroblock connectors to connect your mic-level or line-level audio
sources to these inputs. Each input has a hot (
H
), cold (
C
), and ground (
G
) connector. Inputs 1
and 2 have an additional connector for Page Switch. Remember to adjust the
Gain
knob to set
the input volume level.
4.
Mic
/
Line Gain:
Turn these knobs to set the input gain for each
Mic
/
Line Input
.
5.
Aux In
(
RCA
)
:
Use a standard stereo RCA cable to connect an optional audio source to this
stereo input. When a cable is connected to the
Aux In
on the front panel, these inputs
will be
disabled.
6.
ST Inputs:
Use standard stereo RCA cables to connect line-level audio sources to these inputs.
7.
Mute Connector:
Use a 2-pin Euroblock connector to attach a switch to this connector. The
switch can then mute or unmute the incoming signal from
all
audio sources.
8.
Remote Port:
This port lets you connect a computer to DN-508MXA. Use a 9-pin D-Sub cable
to make this connection. You can use the computer with a third-party utility to manage DN-
508MXA via serial communication.
9.
Remote Extend Port:
This port lets you connect another DN-508MXA to the host device. Use a
9-pin D-Sub cable to make this connection. You can use a computer with a third-party utility to
control all connected DN-508MXA units via serial communication.
10.
RS-422 Port:
This port lets you connect a host device to DN-508MXA. You can then use a third-
party utility to control DN-508MXA via serial communication. Use a standard analog telephone
cable with RJ45 connectors to make this connection.
11.
Ethernet Port:
This port lets you connect DN-508MXA to a network. Connect this port to a
computer via a network switch or router. Alternatively, connect it directly to a computer using an
Ethernet crossover cable. This connection lets you control DN-508MXA though the web
interface.
12.
Speaker Output:
Use Euroblock connectors to connect these outputs to your loudspeakers at
low-impedence (LoZ), high-impedence (HiZ) or BTL (bridge-tied load). When using LoZ, each
group of 2 connections corresponds to 1 zone, for 4 total zones. When using HiZ and BTL, each
pair of groups of 2 connections corresponds to 1 zone, for 2 total zones. Each zone has a
positive (
+
) and negative (
-
) connector. Make sure each loudspeaker is connected to the desired
zone and that the wiring polarity is correct.
13.
Amplifier Input:
Use Euroblock connectors to connect line-level audio sources to these inputs.
Each zone has a hot (
H
) and cold (
C
) connector, and each pair of zones shares the ground (
G
)
connector.
To send audio signal to the
Speaker Outputs
, use the included 5-pin Euroblock with jumper
wires to connect the
Line Outputs
of Zones 1-4 to the
Amp Inputs
of Zone 1-4.
14.
Fan:
The speed of the fan adjusts automatically to cool the unit.
1
2
3
4
5
6
8
10
11
7
9
12
13
14
Summary of Contents for DN-508MXA
Page 2: ......