Denon DMD-F101, Operating Instructions Manual

Page: 5 / 36

5
4 CONNECTIONS
2
When connecting to a receiver other than the D-F101, there is no need to make connection 3. Note that in this case
none of the system functions (auto power on, etc.) will work.
• System operations such as the auto power on function
can only be used if stereo audio cords and system cords
are connected between all the system components. Be
sure to securely connect all the connection cords
between all the units.
• Disconnecting a system cord during system operation
may result in malfunction. Be sure to unplug the power
cords before changing the connections.
• Install the components in such a way that the ventilation
holes of the receiver (DRA-F101) are not obstructed.
• Use the AC OUTLET for audio equipment only. Do
not use them for hair driers, etc.
SPEAKER SYSTEM
SYSTEM
CONNECTOR
PRE
OUT
SUB
WOOFER REC PB
MD TAPE INPUTS
REC PB DVD/AUX CD PHONO
1 AM LOOP ANT.
ANTENNA
2
L
+
-
R
SPEAKER IMPEDANCE 4~16
FM COAX.
75
L
R
AC OUTLET
230V 50Hz
SWITCHED
W MAX
1 2
5
3 4
NOTES:
• Do not plug power cords into power outlets until all
connections have been completed.
• Check the left and right channels and be sure to
interconnect them correctly (L to L, R to R).
• Plug in the power cords securely. Incomplete
connections will result in noise.
• Clasping the power cords and connection cords
together may result in humming or noise.
• After unplugging the power cord, wait at least 5
seconds before plugging it back in.
Recommended System Installation
• To ensure performance and stability, install the D-F101
series as shown below.
• Do not place another component directly on top of the
receiver (DRA-F101).
• For stability, do not stack more than three components
on top of each other.
1
2
3
4
5
Connect the DMD-F101‘s SYSTEM
CONNECTOR jack (1 or 2) to the SYSTEM
CONNECTOR jack (1 or 2) of one of the other
components using the included system cord.
Connect the DMD-F101’s optical digital input
terminal (DIGITAL OPTICAL IN 1 or 2) to the
digital output terminal of the CD player using
optical connection cord.
Plug the power cord into a receiver’s AC outlet or
CD player’s AC outlet.
Connect the DMD-F101‘s LINE OUT jacks to the
receiver’s PB MD jacks using the included stereo
audio cord.
Connect the DMD-F101‘s LINE IN jacks to the
receiver’s REC MD jacks using the included
stereo audio cord.
✽
The DMD-F101 can also be used when connected
to a receiver other than the one in D-F101 series. In
this case, none of the system functions (auto
power on, etc.) will work.
Receiver (DRA-F101) MD recorder (DMD-F101)
1
18T r 0 2 m 4 6 s
-60 40 -30 -20 -12 -6 -2 0
L
dB
R
POWER LOADING MECHANISM
ON / STANDBY
MINIDISC RECORDER DMD-F101
INPUT
- +
MULTI REC CD SRS EDIT
1 3
REC LEVEL
/ ENTER
MEMO REC /
CHARACTER PHONES
SYSTEM
VOLUME
ON / STANDBY
AM-FM STEREO RECEIVER DRA-F101
SOURCE
DIRECT BAND UP DOWN
TUNING
MEMORY
/ SET FUNCTION TIMER TONE RDS
CD SRS REC 0 1 PLAY
CASSETTE DECK DRR-F101
REC CD SRS
PLAY
ON / STANDBY
e
DOLBY NR
ON
OFF
TRACK
ON / STANDBY
COMPACT DISC PLAYER DCD-F101
REPEAT
REVERSE
MODE
(DMD-F101)
(DCD-F101)
(DRA-F101)
(DRR-F101)
Connecting to the D-F101 Series
Cassette deck (DRR-F101)
Power plug
(for U.K. model)
Plug into the open SYSTEM CONNECTOR jack of another
component. Any SYSTEM CONNECTOR jack is OK.
1
18T r 0 2 m 4 6 s
-60 40 -30 -20 -12 -6 -2 0
L
dB
R
POWER LOADING MECHANISM
ON / STANDBY
MINIDISC RECORDER DMD-F101
INPUT
- +
MULTI REC CD SRS EDIT
1 3
REC LEVEL
/ ENTER
MEMO REC /
CHARACTER
For heat dispersal, leave at least 10 cm of space between the top, back and sides of this unit and the wall or
other components.
10 cm or more
5 cm
CD player
(DCD-F101)
Power plug
AC 230 V, 50 Hz
(Plug into a power outlet)