Denon D-T1 Service Manual Download Page 23

Page: 23 / 51

Pin name (function after

reset)

type

I/O

struc-

ture

Notes

Pin functions

Alternate functions

Additional functions

43 PA10

I/O

USART1_RX, TIM1_CH3, TIM17_BKIN I2C1_SDA(2)(5)

44 PA11

I/O

USART1_CTS, TIM1_CH4, EVENTOUT, I2C2_SCL(5)

45 PA12

I/O

USART1_RTS, TIM1_ETR, EVENTOUT, I2C2_SDA(5)

46 PA13 (SWDIO)

I/O

(7)

IR_OUT, SWDIO

47(4) PF6

I/O

(4)

I2C1_SCL(2), I2C2_SCL(3)

47(5) VSS

(5)

Ground

48(4) PF7

I/O

(4)

I2C1_SDA(2), I2C2_SDA(3)

48(5) VDD

(5)

Complementary power supply

49 PA14 (SWCLK)

I/O

(7)

USART1_TX(2), USART2_TX(3)(5), SWCLK

50 PA15

I/O

SPI1_NSS, USART1_RX(2), USART2_RX(3)(5), USART4_RTS(5), EVEN-

TOUT

51 PC10

I/O

USART3_TX(5), USART4_TX(5)

52 PC11

I/O

USART3_RX(5), USART4_RX(5)

53 PC12

I/O

USART3_CK(5), USART4_CK(5), USART5_TX(5)

54 PD2

I/O

TIM3_ETR, USART3_RTS(5), USART5_RX(5)

55 PB3

I/O

SPI1_SCK, EVENTOUT, USART5_TX(5)

56 PB4

I/O

SPI1_MISO, TIM3_CH1, EVENTOUT, TIM17_BKIN(5), USART5_RX(5)

57 PB5

I/O

SPI1_MOSI, I2C1_SMBA, TIM16_BKIN, TIM3_CH2, USART5_CK_RTS(5)

WKPU6(5)

58 PB6

I/O

FTf

I2C1_SCL, USART1_TX, TIM16_CH1N

59 PB7

I/O

FTf

I2C1_SDA, USART1_RX, TIM17_CH1N, USART4_CTS(5)

60 BOOT0

Boot memory selection

61 PB8

I/O

FTf

(6)

I2C1_SCL, TIM16_CH1

62 PB9

I/O

FTf

I2C1_SDA, IR_OUT, SPI2_NSS(5), TIM17_CH1, EVENTOUT

63 VSS

Ground

64 VDD

Digital power supply

1. C13, PC14 and PC15 are supplied through the power switch. Since the switch only sinks a limited

amount of current (3 mA), the use of GPIOs PC13 to PC15 in output mode is limited:

- The speed should not exceed 2 MHz with a maximum load of 30 pF.

- These GPIOs must not be used as current sources (e.g. to drive an LED).

2. This feature is available on STM32F030x6 and STM32F030x4 devices only.

3. This feature is available on STM32F030x8 devices only.

4. For STM32F030x4/6/8 devices only.

5. For STM32F030xC devices only.

6. On LQFP32 package, PB2 and PB8 should be treated as unconnected pins (even when they are not

available on the package, they are not forced to a defined level by hardware).

7. After reset, these pins are configured as SWDIO and SWCLK alternate functions, and the internal pull-

up on SWDIO pin and internal pull-down on SWCLK pin are activated.

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

Summary of Contents for D-T1



















































Search results

Summary of Contents for D-T1

Reviews:

Related manuals for D-T1

Brands by name

Popular brands

Denon D-T1, Service Manual

Search results

Summary of Contents for D-T1

Reviews:

Related manuals for D-T1

Brands by name

Popular brands