Denon AVR-X4300H, Service Manual

Page: 143 / 247

Paths to be confirmed Display Settings What to confirm
3 DIGITAL
(ZONE2)
fig.03a
fig.03b
fig.03c
A03:DIGITAL-Z2
Input Source : Online Music
Input Mode : Auto
Sound mode : STEREO
Amp assign : 7.1ch + ZONE2
Floor Layout : 5ch
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : On
ZONE2 : On
ZONE3 : Off
・ Digital(PCM) input ⇒ Speaker output (Height2 (ZONE2) L/R)
・ Digital(PCM) input ⇒ Pre OUT output (ZONE2 L/R)
( b The input source can be switched to any source except Online Music.)
4 DIGITAL
(ZONE3)
fig.04a
fig.04b
A04:DIGITAL-Z3
Input Source : Online Music
Input Mode : Auto
Sound mode : STEREO
Amp assign : 7.1ch + ZONE
Floor Layout : 5ch
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : On
ZONE2 : Off
ZONE3 : On
・ Digital(PCM) input ⇒ Speaker output (Height2 (ZONE2) L/R)
・ Digital(PCM) input ⇒ Pre OUT output (ZONE2 L/R)
(
b
The input source can be switched to any source except CBL/SAT.)
5 HDMI
fig.05a
fig.05b
fig.05c
A05:HDMI
Input Source : CBL/SAT
Input Mode : HDMI (fixed)
Sound mode : STEREO
Amp assign : 9.1ch
Floor Layout : 5ch&SB
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
・ HDMI input ⇒ Speaker output (Front L/R)
・ HDMI input ⇒ Pre OUT output (Front L/R)
(
b
The input source can be switched to any source except CBL/SAT.)
6 Analog AD
(MAIN)
fig.06a
fig.06b
A06:AD
Input Source : CBL/SAT
Input Mode : Analog (fixed)
Sound mode : MULTI CH STEREO
Amp assign : 9.1ch
Floor Layout : 5ch&SB
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
Speaker Select : Floor & Height
Speaker Config ALL Speaker = Small/SW = Yes(2ch)
MAIN ZONE : On
ZONE2 : Off
ZONE3 : Off
・ Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R, S.Back L/R, Height1 L/R)
・ Analog input ⇒ Speaker output, SW(20Hz) (Front L/R, Center, Surround L/R, S.Back L/R,
Height1 L/R, Subwoofer1/2)
(
b
The input source can be switched to any source except CBL/SAT.)
(
b
Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
7
Analog Amp Assign
(Amp Assign :
ZONE2)
fig.07
A07:ASSIGN-Z2
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z2 Source : Source
Amp assign : 7.1ch + ZONE2
Floor Layout : 5ch
Height Sp : 2ch
Dolby Sp : None
Height Layout : Front Height
MAIN ZONE : On
ZONE2 : On
ZONE3 : Off
・ Analog input ⇒ Speaker output (Height2 (ZONE2) L/R)
・ Analog input ⇒ Pre OUT output (ZONE2 L/R)
( b The input source can be switched to any source except CBL/SAT.)
(
b
Volume 60 is the value when Absolute settings are used. The value is -20 when Relative set-
tings are used)
143
Caution in
servicing
Electrical
Mechanical
Repair Information
Updating