1
Press
SHIFT
to select the memory block (A to G).
2
Press
<PRESET CHANNEL>
or
[CHANNEL + –]
to
select the desired preset channel (1 to 8).
Listening to Preset Stations
n
Default settings
Auto tuner presets
A1 ~ A8
87.5 / 89.1 / 98.1 / 108.0 / 90.1 / 90.1 / 90.1 /
90.1 MHz
B1 ~ B8
522 / 603 / 999 / 1404 / 1611 kHz,
90.1 / 90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
Getting Started
Connections
Setup
Playback
Remote Control
Information
Troubleshooting
Specifi
cations
<SOURCE SELECT> <PRESET CHANNEL>
SHIFT
<STATUS>
<ON/STANDBY>
[iPod]
SHIFT
[SOURCE
CONTROL 1]
[SOURCE
CONTROL 2]
[
8
], [
9
],
[C –]
[
6
], [
7
]
[
2
]
[
1
]
[ENTER]
[
uip
]
[POWER OFF]
[iPod]
[MODE]
[ENTER]
[ –]
[
uip
]
[Front]
[Rear]
Button located on both the main unit and the remote control
unit
BUTTON
Button only on the main unit
<BUTTON>
Button only on the remote control unit
[BUTTON]
Symbols used to indicate buttons in this manual
iPod® Playback
The music on an iPod can be played by using the control dock for
iPod (ASD-1R, ASD-3N or ASD-3W, sold separately).
The operation can also be performed using the buttons on the
remote control unit.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b
The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
1
Make the necessary preparations.
q
Set the iPod in the DENON control dock for iPod.
(
v
See the control dock for iPod’s operating instructions.)
w
Assign the control dock for iPod’s input.
The input for the control dock for iPod is assigned to VCR by
default.
“System Setup”
–
“Input Setup”
–
“iPod Assign”
(
v
page 21)
Preparations
2
Either turn
<SOURCE SELECT>
or press
[iPod]
to
select the input source assigned in step 1-
w
above.
3
Set
[SOURCE CONTROL 1]
to “AUDIO” and
[SOURCE
CONTROL 2]
to “iPod/NETWORK”.
(
v
page 36 “Remote Control Unit Operations”)
4
Press
[MODE]
and hold it down for a 2 seconds or
more to select the display mode.
To switch between modes, press and hold down the button.
When remote mode is active, “Remote” is displayed.
[Selectable mode]
Browse mode
Remote mode
Display location
Main unit display
iPod display
Playable
files
Audio file
S
S
Video file
Sz
1
Sz
2
Active
buttons
Remote
control unit
(AVR-589)
S
S
iPod
A
S
z
1
: When using an ASD-3N or ASD-3W control dock for iPod
.
z
2
: Video may not be output, depending on the combination of
ASD-1R and iPod.
• With the default settings, the iPod can be used connected to the
VCR (iPod) connector.
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio fi les and achieve a richer sound.
The default setting is “Mode3” (
v
page 28).
• Press
<ON/STANDBY>
or
[POWER OFF]
and set the AVR-589’s power
to the standby mode before disconnecting the iPod. Also switch the
input source to one to which “iPod Assign” is not assigned before
disconnecting the iPod.
• When using an ASD-3N or ASD-3W control dock for iPod, refer to
the respective manual to operate.
