background image

7

S500 Plus 

SP20003_REV_1

Important Safety Instructions

In order to operate the machine safely please follow these Health and Safety guidelines.

TRAINING

READ THE INSTRUCTIONS CONTAINED IN THIS MANUAL WITH CARE. IF YOU ARE IN 
ANY DOUBT PLEASE ASK YOUR EMPLOYER OR CONTACT US DIRECT AT 

DENNIS

.

CAUTION

• 

Be familiar with the controls and the proper use of the equipment.

• 

Never allow children or people unfamiliar with these instructions to use the mower. Local regulations or insurance may  

  restrict the age of the operator.

•  

Never mow while people, especially children, or pets are nearby.

•  

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their

 property.

PREPARATION

•  

While operating always wear substantial footwear and long trousers. Do not operate the mower barefoot or in open  

 sandals.

•  

Thoroughly inspect where the equipment is to be used and remove all stones, sticks, wire, bones and other foreign objects.

PETROL IS HIGHLY FLAMMABLE AND WILL DAMAGE GRASS IF SPILT.

WARNING

A)  Store fuel in containers specifically designed for this purpose.

B)  Refuel out doors and do not refuel whilst smoking.

C) Add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the engine is running or  

  when the engine is hot.

D) If petrol is spilled do not attempt to start the engine but move the machine away from the area of spill and avoid

  creating any sources of ignition until the vapours have dissipated.

• 

Replace damaged or faulty silencers.

• 

Before using the machine always inspect the safety devices including the cut off switch and the blades for excessive  

  wear or damage. Replace if necessary.

OPERATION

•   Do not operate the engine in a confined space where dangerous 

CARBON MONOXIDE

 fumes can collect.

•   Operate only in daylight or good artificial light.
•  

Always be sure of your footing on slopes.

•  

Walk. Never run.

•  

Walk across the face of slopes, never up and down.

•  

Exercise extreme care on slopes when changing direction.

•  

Do not operate excessively steep slopes.

•  

Use extreme caution when reversing or pulling the machine towards you.

•  

Never operate with defective guards or shields.

•  

Do not change the engine governor settings or overspeed the engine.

•  

Start the engine carefully following the instructions with feet well away from the blades.

•  

Do not tilt the machine when starting the engine.

•  

Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

•  

Never pick up or carry the machine while the engine is running.

Summary of Contents for S500 PLUS























Reviews: