manualshive.com logo in svg

Dennard 2055, Menu System Manual

Share
Download
Dennard 2055 Menu System Manual Download Page 26

 

APPENDIX .2.

 

TROUBLE SHOOTING GUIDE 
 

PROBLEM ACTION 

No picture 

Check the PSU fuses 
Check the input and output voltages 
Check all co-ax connections 
Continuity check the dome multicore cable:- 

Pin1 

=Video 

Pin 2 

=Video screen 

Pin3 

=Data + (Yellow) 

Pin4

 =Data(Green) 

Pin 5 

=24Volt Neutral (blue) 

Pin 6 

=24Volt  Live (red) 

Pin

     =  Earth (drain wire) 

Picture with no 
control 

If control is via a 

drx100 

protocol converter, check that the Green and Yellow 

wires from the dome are connected correctly ie Green to C1 Yellow to C2. 
 
If control is via RS485 check that the data connections are:-  
Green Wire data  -          Yellow Wire data + 
 
If control is via a 2055 co-ax (which has built in protocol converters), control is 
"up the co-ax" but the address switches have to be set to suit the controller 
protocol 

See page 10 of the Type 2055 product handbook for settings

.

  

 

Picture with 
intermittent control 

This problem is often due too to much or too little video gain. 
If you are using the 2055 co-ax dome with built in protocol converters, video 
amplification is accessed through the menu system. Open the 

Technician Menu

  

enter the password 

PIN

, select 

Miscellaneous Services

 from the next menu 

then select 

Set Video Amplification. 

Adjust the gain to suit. 

 
If you are using a 2055drx then the Video Gain can be found on the drx card  
behind the BNC connectors located in the PSU box

 

 

Flashing cursor size 
box top right corner 
of monitor 

This indicates that the 2055 software has detected an error. Before contacting 
Dennard Technical on 01420 485713   the error display should be enabled as 
this will help Dennard Technical to solve your problem. You need to open the 

Technicians Menu

 enter the password 

PIN

, select 

Enable /Disable Options

  

and select 

Enable Error display. 

A message will then appear at the bottom of 

the monitor screen 

On Baxall controlled 
Domes, alphabet 
menu pops up 
when the joystick is 
touched 

This is because the Baxall controller has been configured to 

ALTERNATE

 mode 

which is not supported by the 2055. Setting the dome to 

STANDARD

 mode with 

Rx

 set to 

DC

 will solve the problem.  

On Dennard & BBV 
controllers the 
dome spins 
continuously 

Could be due to no dead band on the joystick caused by the joystick being off 
centre on power up. Power the controller down then power up again ensuring 
that the joystick is free to self-centre. 

 

2055  

Menu

 

System Manual

 

Appendix 2 

                                                                          

Sheet.A2-1 

Summary of Contents for 2055

































Reviews:

No comments

Brands by name

Popular brands

Load more brands