manualshive.com logo in svg

Dennard 2055, Menu System Manual

Share
Download
Dennard 2055 Menu System Manual Download Page 18

 

The final choice 

Set video amplification 

enables boost and lift for the video to 

compensate for different types/lengths of coax. Selection introduces a further menu ie: 

 

Video gain 1 / normal 
Video gain 2 
Video gain 3 
Video gain 4 / max 
Video lift off 
Video lift on 
Exit 
 

Video gain is factory set at 1 with Video lift off, different settings are made in the usual 
way. A double arrow to the right of the command indicates the current choice.  
 
The 

Technician Menu 

 seventh option allows the password to be changed and is the 

same procedure as used on the Supervisor Menu password change ie: 

 

Enter PIN   _ _ _ _ 
 
0 1 2 3 4 5 6 7 8 9 
 
Accept Entry 
Clear Entry 
Cancel 

 
 
 
 
 

 
5.0 

Menu Flow Chart 

 

The three sheets can be removed and joined to produce a full flow diagram of the menu 
system. 
 
 
 
 

APPENDIX.1.

 

 2055 programme access from various controllers

 

 
 

 

APPENDIX.2.

 

Trouble shooting guide 

 
 
 
 
 
 
 

 

 
2055  

Menu System Manual

                                                                                                  

Sheet.17 

Summary of Contents for 2055

































Reviews:

No comments

Brands by name

Popular brands

Load more brands