manualshive.com logo in svg

Denison Hydraulics P140 A-mod, Service Information

Share
Download
Denison Hydraulics P140 A-mod Service Information Download Page 3

3

Specification

• compensator response

off-stroke
on-stroke

• compensator adjustment

• minimum compensating pressure (comp, torque limiter)

• minimum compensator override pressure (servo, electric
& hyd. str.)

• torque limiter  adjustment range

code J
code K

• typ. servo & stroker response @  83 bar  servo pressure,
zero to full stroke and vice versa

• servo flow required for this response (E, H, R10 controls)

• servo flow required for this response (*1J, *1K, *1P
controls)

• maximum servo pressure

• servo shaft rotation, 0 to full volume

• displacement/rev./degree servo shaft rotation

• hydraulic stroker control pressure

0 displacement
full displacement

• electric stroker control amps (24v.)

0 displacement
full displacement

pulse width modulation frequency:
mating connector: Din 43650 type AF 
part no. 167-10008-8 (provided)

• electric stroker nominal coil resistance (24v. coil)
• electric stroker nominal coil resistance (12v. coil)

• handwheel turns, full to zero stroke

• torque to turn handwheel @ 70 bar
• torque to turn handwheel @ 500 bar

• torque to turn rotary servo shaft

• port C1, C2 (cylinder gage ports)
• port E (electric stroker control pressure inlet)
• port H (hydraulic stroker control pressure inlet)   
• port LS (load sensing port) 
• port V (compensator vent) 
• port X (rotary servo, electric & hydraulic stroker servo
inlet)

Term

sec.
sec.

bar/turn

bar

bar

Nm
Nm

sec.

l/min.

l/min

bar

degrees

cc/rev/deg.

bar
bar

mA
mA
Hz

ohms
ohms

turns

Nm
Nm

Nm

BSPP
BSPP
BSPP
BSPP
BSPP
BSPP

P260

0,100
0,150

138

17,2

93,1

282 - 706

706 - 1129

<0,6

11,4

15,2

103

80

3,25

3,45

19

150-200

390

100-150

41
10

10

17
40

2,3

1/4
1/4
1/4
1/4
3/8
3/8

TYPICAL CHARACTERISTICS

FLUID CONNECTIONS

CHARACTERISTICS

www.comoso.com

Summary of Contents for P140 A-mod

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands