manualshive.com logo in svg

Denison Hydraulics P140 A-mod, Service Information

Share
Download
Denison Hydraulics P140 A-mod Service Information Download Page 26

1. See Figure 12.

Remove 2 screws holding Torque Limiter body (16) to cap 

assembly (1).

2. Remove all parts from torque limiter body (16) except pin (30) and arm assembly
(28). It is not necessary to remove these parts unless broken or worn. Examine parts for
wear or damage.

3. Remove screw (3). Examine head for excessive wear, and body for smooth sealing
surface with O-ring.

4. Remove maximum stop handwheel assembly or maximum stop screw assembly.

5. Remove cap assembly (1).

6. See Figure 13  Remove plug (15) and attached parts. Remove spring (11) and spool
(18).

7. Remove adjusting plug (2) and attached parts. Remove spring ( 7 ) and cone (8).

8. Do not remove sleeve in body (1). Sleeve is pressed into cap and finished to size. If
sleeve or cap is worn, replace the cap-sleeve assembly (1).

9. Examine seat (10) for wear. Do not remove unless damaged.

1. See Figure 13  Install Avseal plugs (9) and orifice (19)  in body.

2. Press seat (10) into bore squarely against shoulder in bore.

3. Install spool (18) into bore as shown. Install spring (11) over end of spool. Install O-
ring (6) on seal (16). Lubricate and install into plug (15). Install plug (15) into cap. Install
screw (3), nut (4) and acorn nut (17). Install plug (12). Torque plugs to 60 Nm. Install plug
(21). Torque to 35 Nm. Install plug (28). Torque to 30 Nm.

4. Install O-ring (6) on seal piston (5). Lubricate O-ring and Install cone (8), spring (7)
and seal piston (5) into bore in cap (1), being careful that cone enters seat (10). Install
adj. plug (2), screw (25), nut (4) and acorn nut (26).

5. Carefully  install O-ring  (27) in the cap.

6. Note proper location for control cap. Install O-rings on interface between cap and
pump control pad. Install cap, guiding control piston into bore. Torque mounting screws
to 101 Nm.

7. Install maximum volume handwheel or screw assembly. Set stop to clear control pis-
ton.

8. See Figure 12. Apply Loctite

®

on threads of screw (3), lubricate the shank, thread

through the cap into the control piston,  and torque to 6,78 Nm

9. Measure height from control cap to top of screw. With control piston at full stroke,
dimension must be 38,1 +/- .76 mm.

10. Press dowel (30) into body (16), through the link assembly (28), to 6,35 mm below
surface. Apply Loctite

®

to threads of screws (35) and install over dowel (30).

11. While sleeve (27) is engaged into dowel on link (28), slide spool (21) into bore of
body (16), and through sleeve (27). Spool (21) must move freely and easily at all posi-
tions of the link (28).

12. Assemble remaining parts per drawing. While spring retainer  is engaging clevis pin
(5) under dowel of link (28), slide the other opening of spring retainer  over the top of the
screw (3). Attach body assembly (16) to cap (1) and torque screws to 102 Nm.

TORQUE LIMITER

TORQUE LIMITER
DISASSEMBLY

ASSEMBLY

26

www.comoso.com

Summary of Contents for P140 A-mod

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands