background image

demig Prozessautomatisierung GmbH

 

 

Manual Terminal DE-BT 1000 

Chapter: Introduction  

  1 

1. 

Chapter: Introduction 

1.1 

Basic Information 

1.1.1. 

General Handling 

Please  read  the  operating  instruction  carefully  before  installing  or  handling  the 
industrial terminal DE-BT 1000, in order to avoid dangerous situations and damages 
due to operating errors. This operating manual is limited to the handling of the  
DE-BT 1000 and does not include all different applications. 

1.1.2. 

CE-Conformity 

The  industrial  terminal  DE-BT  1000  corresponds  to  the  standards  and  guidelines 
named in the conformity declaration. To make sure these are observed, please pay 
attention to the following:

 

 

It  is  the responsibility  of  the installing  person  to  observe  all  the  standards  and 
guidelines for the usage and installation of the industrial terminal DE-BT 1000. 

 

Make sure that only qualified staff installs the industrial terminal DE-BT 1000. 

 

Make  sure  that  all  the  precautions  stated  in  the  chapter  "Information  for  the 
installation" are observed. 

 

Reparations  of  the  industrial  terminal  DE-BT  1000  by  the  customer  are  not 
allowed. 

 

By  using  the  industrial  terminal  DE-BT  1000  for  unintended  purposes  as  well 
violating the regulations mentioned above, demig Prozessautomatisierung GmbH 
assumes no responsibility. The conformity declaration then loses its validity. 

1.1.3. 

Installation Instructions 

Please  check  the  process  control  system  immediately  upon  receipt.  In  case  of  any 
damages, the device must not be installed. Pay attention to the terms of installation in 
chapter service and technical data. 

 

 

 

Summary of Contents for DE-BT 1000


























Reviews: