Delta RTU-ECAT Operation Manual Download Page 76

Page: 76 / 79

Chapter 8 Error Diagnosis and Trouble-shooting

8-3

EtherCAT LED

LED

LED status

Indication

How to correct

Green

light

The EtherCAT port has been
connected to the EtherCAT
network.

OFF

The EtherCAT port has not yet
been connected to the EtherCAT
network.

Ensure that the hardware connection to
the EtherCAT port is proper.

Yellow

light

Blinking

Data are being transmitted or
received via the EtherCAT port

No data are being transmitted or
received via EtherCAT port.

Add RTU-ECAT to the master.

OFF

There is no hardware
connection to the EtherCAT port.

Ensure that the hardware connection to
the EtherCAT port is proper.

8.2

Status Indication Diagnosis

The status indication parameters of RTU-ECAT are used to display the operating states of special modules
and DI/DO modules. See section 6.3.2 for details on related status indication parameters.

Summary of Contents for RTU-ECAT
















































































Search results

Summary of Contents for RTU-ECAT

Reviews:

Related manuals for RTU-ECAT

Brands by name

Popular brands

Delta RTU-ECAT, Operation Manual

Search results

Summary of Contents for RTU-ECAT

Reviews:

Related manuals for RTU-ECAT

Brands by name

Popular brands