background image

18

Quick installation guide for RPI H3 inverters EU EN 5013227802 02 2016-01-05

Commissioning - basic settings

11

To execute commissioning, the inverter needs to be pow-
ered either by AC (the grid) or DC (the solar modules)

    N e x t   /   E n t e r  

        U K   G 8 3 - 2

1. 

Use the button 

SEL

 to select your country or grid.

To conirm your selection, press the button 

ENT

.

          N   /   Y  

          E x i t   ?

2. 

To inish the country selection, press the button 

ENT

.

To select another country or grid, press the button 

SEL

 and repeat step 1.

 

þ

The basic setup is inished. The main menu is shown.

          3 . 0   k V A

        I n v e r t e r

Setting the inverter ID

If your PV plant contains multiple inverters, for each of the inverters a different inverter ID has to be set.
The inverter ID is needed to identify each inverter via RS485. For a description of the RS485 connection, 
see “Connecting to a datalogger via RS485”, p. 14.

        I D   :   1

        I n v e r t e r

1. 

In the main menu, use the button 

SEL

 to select 

Inverter ID

.

2. 

Press the buttons 

SEL

 and 

ENT

 at the same time and hold them for at least 3 seconds.

 

The menu to change the inverter ID is shown.

      I D   =   1     ?

    S e t t i n g   I D :

      I D   =   2     ?

    S e t t i n g   I D :

3. 

Use the button 

SEL

 to change the inverter ID. 

4. 

To conirm the value, press the button 

ENT

.

 

The new inverter ID is shown in the main menu.

        I D   :   2

        I n v e r t e r

Commissioning - Further settings (optional)

12

Summary of Contents for RPI H3 110

























Reviews: