2
Fig. 6
o
F
5. attach lathe stand platform (F) Fig. 6 using two 3/8-16 x 3-1/2"
(89 mm) hex head bolts (C) Figure 1, two 3/8 flat washers (D) Fig.
1 and two 3/8-16 nylock nuts (a) Fig. 1.
NoTE:
the stand height is adjustable by placing the hex head bolt
through two of the four holes (N) in the lathe stand platform (Figure
6). Be sure the holes (o) in platform are facing to outside, away from
tool holder as shown. always use two bolts to attach the platform.
6. to attach, place two washers on two bolts and insert bolts
through desired holes (N) Fig. 6. Place second washer on bolts
and then tighten with 3/8-16 nylock nuts.
NoTE: Do not tighten completely.
SToP:
If you have purchased the 46-464 Lathe Stand
Extension with the 46-462 Lathe Stand, the remaining assembly
steps are described in the section of the 46-464 manual titled
Assembly of Exension To The Stand. otherwise, continue:
7. attach right leg and lathe stand platform in the manner described
above. Note the proper orientation of feet and platform as shown
in Figure 8.
8. Place lathe (P) Fig. 7 on top of both lathe stand platforms - one
shown at (F) - and line up holes in lathe base with holes in
platform.
9. attach lathe to stand at these holes using four 3/8-16 x 1-1/2"
(38 mm) hex head bolts (B) Figure 7, eight 3/8 flat washers and
four 3/8-16 nylock nuts (a).
10. For each hole, place a washer (not shown) on the hex head bolt
and insert it down through the hole at (B) Fig. 7. Place a second
washer on bolt underneath and tighten securely using nylock nut.
11. adjust leveling feet so the lathe stand rests securely on the floor
without rocking or tilting. then tighten all four jam nuts.
12. securely tighten all stand hardware.
13. Completed assembly will look like Figure 8.
TRoUBLESHooTING
For assistance with your machine, visit our website at
www.
deltaportercable.com
for a list of service centers or call the DELta
machinery help line at 1-800-223-7278 (in Canada call 1-800-463-
3582).
Fig. 8
N
Fig. 7
P
F
B
a
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts
list or to order parts, visit our website at www.
deltaportercableservicenet.com. You can also
order parts from your nearest factory-owned
branch, authorized warranty service Center or
by calling End User services at (800) 223-7278
to receive personalized support from one of our
highly-trained representatives.
FREE WARNING LABEL REPLACEMENT
if your warning labels become illegible or
are missing, call 1-800-223-7278 for a free
replacement.
SERVICE AND REPAIRS
all quality tools will eventually require servicing
and/or replacement of parts. For information
about DELta machinery, its factory-owned
branches, or to locate an authorized warranty
service Center, visit our website at www.
deltaportercable.com or call our End User
services at (800) 223-7278. all repairs made by
our service centers are fully guaranteed against
defective material and workmanship. we cannot
guarantee repairs made or attempted by others.
By calling this number you can also find answers
to most frequently asked questions 24 hours/day.
You can also write to us for information at DELta
machinery, Po Box 2468, Jackson, tennessee
38302-2468 - attention: End User services. Be
sure to include all of the information shown on
the nameplate of your tool (model number, type,
serial number, date code, etc.)
ACCESSoRIES
Since accessories other than
those offered by DELTA have not been tested
with this product, use of such accessories could
be hazardous. For safest operation, only DELTA
recommended accessories should be used with
this product.
TO REDUCE THE RISK OF INJUR
Y,
READ THE TOOL AND TOOL ST
AND INSTR
UCTIONS BEFORE USE.
FOR
USE
WITH 46-455
AND 46-460 LA
THES ONL
Y. F
ASTEN
TOOL
TO ST
AND BEFORE USE.
MAXIMUM LOAD 200
LBS (90 KG).
DO NOT CLIMB,
SIT OR ST
AND ON LA
THE ST
AND.
DO NOT USE ON SLOPED,
UNEVEN OR UNST
ABLE SURF
ACES.
USE ONL
Y
FROM
THIS SIDE.
PARA REDUCIR EL RIESGO DE LESIONES,
LEA LAS INSTR
UCCIONES DE LA HERRAMIENT
A Y LA
BASE ANTES DE USAR.
P
ARA UTILIZAR CON LOS
TORNOS 46-455
Y 46-460 SOLAMENTE.
ASEGURE
LA HERRAMIENT
A
A LA BASE
ANTES DE USAR.
CARGA MÁXIMA:
90 KG (200 LIBRAS) NO SE SUBA,
SE SIENTE NI SE P
ARE SOBRE LA
BASE DEL
TORNO.
NO LO UTILICE SOBRE UNA SUPERFICIE DESNIVELADA,
DISP
AREJA O INEST
ABLE.
USE SOLAMENTE DE ESTE LADO.
POUR RÉDUIRE LE RISQUE DE BLESSURES,
LIRE LE MODE D’EMPLOI DE L
’OUTIL ET DE SON
SOCLE A
VANT L
’UTILISA
TION.
POUR LES
TOURS 46-455 ET 46-460 SEULEMENT
. FIXER L
’OUTIL
AU SOCLE
AV
ANT L
’UTILISA
TION.
CHARGE MAXIMALE DE 90 KG (200 LB).
NE P
AS GRIMPER,
S’ASSEOIR OU SE
TENIR DEBOUT SUR LE
SOCLE DU
TOUR.
NE P
AS UTILISER LE SOCLE SUR DES SURF
ACES INCLINÉES,
INÉGALES OU INST
ABLES.
N’UTILISER QUE DE CE CÔTÉ.
M
od
. 4
6-
46
2
DE
LT
A
M
ac
hi
ne
ry
: J
ac
ks
on
, T
N
3
83
05
M
ad
e
in
T
ha
ila
nd
/
Fa
br
ic
ad
a
en
T
ai
la
nd
ia
/
Fa
br
iq
ué
à
T
ha
ïla
nd
e
Summary of Contents for 46-462
Page 7: ...7...
