background image

SWITCH

The switch (A) Fig. 17, is located on the front of the drill
press head. To turn the drill press “ON” move the switch
to the up position. To turn the drill press “OFF” move the
switch to the down position.

LOCKING SWITCH IN
THE “OFF” POSITION

We suggest that when the drill press is not  in use, the
switch be locked in the “OFF” position. This can be done
by grasping the switch toggle (B) and pulling it out of the
switch, as shown in Fig. 18. With the switch toggle (B)
removed, the switch will not operate. However, should
the switch toggle be removed while the drill press is
operating, the switch can be turned “OFF” once, but
cannot be restarted without inserting the switch toggle
(B) Fig. 18.

TABLE ADJUSTMENTS

1.

The table can be raised or lowered on the drill press
column by loosening the table locking lever (A) Fig.
19, and turning the table raising and lowering handle
(B). After the table is at the desired height, tighten
locking lever (A). NOTE: Final positioning of the drill
press table should always be from the bottom to the
up position.

2.

The table can be rotated 360 degrees on the column
by loosening locking lever (A) Fig. 19, rotate table to
desired position and tighten locking lever (A).

Fig. 17

Fig. 18

Fig. 19

Summary of Contents for 14-070



















Reviews: