background image

 

MACRO-CPU Hardware Reference

 

U MACRO-CPU HARDWARE MEMORY MAP 

The values in this table represent the hardware locations associated with register-based transactions that occur in 
the 3U MACRO-CPU.   

 

Reference ADDR 

(hex) 

Description 

CS00- 

$FFC0 

Stack I/O select #1 

CS02- 

$FFC8 

Stack I/O select #2 

CS04- 

$FFD0 

Stack I/O select #3 

CS06- 

$FFD8 

Stack I/O select #4 

CS0- 

$C000 

Stack axis 1-4 select 

CS1- 

$C020 

Stack axis 5-8 select 

CS2- 

$C040 

UBUS backplane axis 1-8 select 

CS3- 

$C060 

UBUS backplane axis 5-8 select 

CS4- 

$C080 

On-board DSPGATE2 select 

CS4X- 

$C0C0 

UBUS backplane MACROgate or DSPgate2 select (CS4- on UBUS) 

CS10- 

$FFE0 

UBUS backplane I/O select #1 

CS12- 

$FFE8 

UBUS backplane I/O select #2 

CS14- 

$FFF0 

UBUS backplane I/O select #3 

CS16- 

$FFF8 

UBUS backplane I/O select #4 

MEMCS0- 

$D000 

UBUS hardware I/O field (was DPRCS-) 

MEMCS1- 

$E000 

UBUS hardware I/O field (was VMECS-) 

 
The addressing field size is 16-bits in the 3U MACRO-CPU.  The address table above is similar to the PMAC2 
product line. 

 

U MACRO-CPU Hardware Memory Map 

28

Summary of Contents for 3A0-602804-10x




































Reviews: