Delta OHM HD45 17A Operating Manual Download Page 66

Page: 66 / 74

HD45 / HD46

- 66 -

V2.4

Examples:

HD45

7BDVR:

Transmitter, indicator and regulator for temperature and CO

. With

display, two 0÷10V analog outputs, a relay configurable for temperature or CO

control.

HD45

BVR:

Transmitter, indicator and regulator for CO

. Without display, with CO

level LED indicators, with 0÷10V analog output and relay.

HD45

17AR:

Transmitter and regulator for temperature and humidity. Without

display, with two 4÷20mA analog outputs, a relay configurable for temperature or
humidity control.

HD45

17DV:

Transmitter and indicator for temperature and humidity. With display,

two 0÷10V analog outputs, without relay.

HD45

7BSR:

Transmitter and regulator for temperature and CO

. Without display,

with RS485 output, without analog output, with a relay configurable for
temperature or CO

control.

HD46

17BDV:

Transmitter and indicator for temperature, humidity and CO

. With

display, without keyboard, with three 0÷10V analog outputs, without relay and
without RS485 output.

HD46

17BDTSR:

Transmitter, indicator and regulator for temperature, humidity and

. With display and keyboard, with three relay outputs, with RS485 output.

HD46

17S:

Temperature and humidity transmitter. Without display and keyboard, no

relays, with RS485 output.

Accessories:

DeltaLog14:

Software for connection to a PC through serial port with mini-USB

connector, instrument configuration and data download. For Windows

operating

systems.

HDM46:

Calibrated relative humidity and temperature replacement module (for

HD46…models only).

RS45:

Not isolated serial connection cable with built-in adapter. USB connector to PC

and mini-USB connector to instrument serial port. The instrument is powered by
the PC through the cable (at least a 500 mA USB port is required).

RS45I:

Isolated serial connection cable with built-in adapter. USB connector to PC

and mini-USB connector to instrument serial port. The instrument is not powered
by the PC.

Windows and Windows Vista are registered Microsoft Corporation trade marks.

Summary of Contents for HD45 17A











































































Search results

Summary of Contents for HD45 17A

Reviews:

Related manuals for HD45 17A

Brands by name

Popular brands

Delta OHM HD45 17A, Operating Manual

Search results

Summary of Contents for HD45 17A

Reviews:

Related manuals for HD45 17A

Brands by name

Popular brands