TYXIA 411
Lighting receiver switch
Installation and User Guide
Device complying with the requirements of the
R&TTE 1999/5/EC directives
*2701934_rev1*
Because of changes in standards and equipment, the characteristics given in the
text and the illustrations of this document are not binding unless confirmed by
Delta Dore.
DELTA DORE
Bonnemain - 35270 COMBOURG - France
E-mail : [email protected]
• Carefully read these instructions prior to instal-
lation.
• The unit must be installed in compliance with
currently applicable standards.
• Always switch off the mains before installing or
servicing the unit.
• Do not attempt to repair the unit yourself; an
after-sales service is available.
• Check that the fastenings are suited to the sur-
face that the unit will be attached to (plaster-
board, brick, etc.).
• The diagrams provided are simplified for grea-
ter clarity. The protective units and other
accessories required by the standards are not
illustrated.
Standard UTE NF C15-100 and good practice
must be complied with. Connected or nearby
equipment must not generate excessive inter-
ference (directive 2004/108/EEC).
Warnings
Your unit comes with a plastic protection that must
be removed when work is complete (for example
after painting), before replacing the cover plate
(Delta Dore brand located in the lower right).
Location
The receiver must be fitted on a flush-mounted box
(Ø 65 mm) that will receive the live and neutral
wires.
Connecting and mounting the product
Connect the product
(see adapted connec-
tion according to your
application), then posi-
tion it by orienting the
terminal upwards.
Secure it by tightening
the screws without for-
cing them.
Plastic
protection
Installation
Operation with a transmitter
associated TYXIA or TYDOM
Press the receiver button
until the LED flashes (~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode.
Press the receiver
button to pass from one
rate of flashing to the other.
Select the rapid flashing.
IMPORTANT: The receiver is delivered in simple
lighting mode. To use it in remote control switch
mode, it must be associated with a transmitter.
The remote control switch mode can only be
controlled by a
(TYXIA) or
(TYDOM 200
button).
or
(status being modified)
Connection
Operating the TYXIA 411
Pressing the
button changes the current state
(on or off).
TYXIA 411
Remote control switch
L
N
L
N
230 V
50 Hz
T L R N N
IMPORTANT:
Do not connect
terminal 3 for
this application.
Remote control switch mode
Connection
Operating the TYXIA 411
Pressing the
button changes the current state
(on or off).
L
T L R N N
N 230 V
50 Hz
Existing
switch
TYXIA 411
Two-way switch mode
On the transmitter, press and hold the
button
for 5 seconds. The LED will light up, go out, then
light up again. Release.
Check that the receiver’s LED is no longer flashing.
The transmitter
button is associated with
the receiver in remote control switch mode.
To link a TYXIA 411 with a TYDOM 200, please
refer to the TYDOM 200 guide.
On the transmitter, press and hold the
button
for 5 seconds. The LED will light up, go out, then
light up again. Release.
Check that the receiver’s LED is no longer flashing.
The
transmitter button is linked with the
receiver in two-way switch mode.
To link a TYXIA 411 with a TYDOM 200, please
refer to the TYDOM 200 guide.
Operation with a transmitter
associated TYXIA or TYDOM
Press the receiver button
until the LED flashes
(~3 seconds).
2 possible choices.
Slow flashing: two-way switch mode
Rapid flashing: remote control switch mode (unused).
Press the receiver
button to pass from one rate
of flashing to the other.
Select the slow flashing.
IMPORTANT: he two-way switch mode can only be
controlled by a
(TYXIA) or
button
(TYDOM 200).
or
(status being modified)
Connection
Operating the TYXIA 411
Pressing the
button changes the current state
(on or off).
L
N 230 V
50 Hz
T L R N N
TYXIA 411
Simple lighting mode
Associating a
button (scenario)
On the receiver, set the appliance to the required
status (e.g. light off), then press the receiver button
until the LED flashes (~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver
button to pass from one rate
of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold the
button
down for approximately 5 seconds. The LED will light
up, go out, then light up again. Release.
Check that the receiver’s LED is no longer flashing.
The transmitter
button is associated with the
receiver.
A
button can control different receivers simulta-
neously (roller blinds, dimmer, simple lighting, etc.).
Associate buttons
Press the receiver button
until the LED flashes
(~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver
button to pass from one rate
of flashing to the other.
Select the slow flashing.
On the transmitter, simultaneously press and hold
the and buttons
for
approximately
5
seconds, until the LED comes on.
Release.
Check that the receiver’s LED is no longer flashing.
The transmitter buttons
and
are associated
with the receiver.
Associating a
button
Press the receiver button
until the LED flashes
(~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver
button to pass from one rate
of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold the
button
down for approximately 5 seconds. The LED will light
up, go out, then light up again. Release.
Check that the receiver’s LED is no longer flashing.
The transmitter
button is associated with the
receiver.
Simple lighting mode with an associated TYXIA transmitter
The simple lighting mode can be controlled by a
TYXIA transmitter (transmitter switch, key ring
remote control, etc.).
(recommended for controlling
exterior lighting)
OFF
ON
OFF
ON
OFF
ON
Either is possible, depending on the scenario.
or
The receiver can record up to a maximum of 8
associations (buttons, transmitters, etc.).
The receiver is compatible with:
incandescent lamps
(1000 W), 230V halogen
lamps (1000
W),
low-consumption
lamps
(300 W), halogens with electronic transformers
(300 W) and 230V halogen lamps with TBT ferro-
magnetic transformer (300 W).
The receiver is incompatible with:
fluorescent lamps, motors and controlling hi-fi or
video products.
