background image

2

PARTS: 

HARDWARE KITS PART #21396

C. CRESCENT WASHER x12

ALLEN WRENCH

A. 50mm Bolt x16

B. 30mm Bolt x4

D. WOOD DOWEL x32

E. KNOB SCREW x8

F. SCREW x16

H. DRAWER SCREW x36

PHILLIPS SCREWDRIVER

       NOT INCLUDED

WARNING:

 

Serious or fatal crushing injuries can occur from furniture tip-over.  To help prevent tip-over:

.

Place heaviest items in the lowest drawers.

.

Unless specifically designed to accommodate, 

do not

 set TV’s or other heavy objects on the top of this 

product.

.Never

 allow children to climb or hang on drawers, doors,or shelves.

.Never

 open more than one drawer at a time.

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

.

Always monitor your child’s activity when in the nursery.

.Do not

 allow standing in drawers.

.Do not

 allow standing on top of this product.

.

Accessory Items must be securely fastened to this product according to the instructions provided with 

those items.

.

To avoid head injury, do not allow children to play underneath open drawers.

.

Do not leave drawers open when not in use.

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on 

the diagram of the item which is drawn actual size and design. Be sure to use the proper size and 

shape specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly 

recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON CARE AND MAINTENANCE:

Do not

 scratch or chip the finish.

- Inspect the product periodically, contact delta children's products for replacement parts or questions.

Do not

 store the product or any parts in extreme temperatures and conditions such as a hot attic or a 

damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or 

felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.  

-

Do not

 use abrasive chemicals.  

-

Do not

 spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

G. KNOB x8

Part# 21377

Summary of Contents for 74104 Series











Reviews: