15
Place an empty container with a minimum capacity of
57.48 fl.oz./1.7 litres under the hot water spout (A18).
4. Wait for the
(B2) and
(B4) lights to come
on steadily.
Important! Danger of burns!
Hot water containing acid flows from the cappuccino maker
(A9). Avoid contact with splashes of water.
5. Press the
button (B14) and hold it down for at least
5 seconds to confirm that you have added the solution
and begin the descaling procedure. The light in the button
remains on steadily to indicate that the descaling pro-
gramme has begun. The
,
and
(B6)
lights flash simultaneously telling you to turn the steam
knob to the l position (coffee cannot be made).
6. Turn the steam/hot water knob (B10) anticlockwise to the l
position. The descaler solution flows out of the cappuccino
maker into the underlying container.
The descale programme automatically performs a series of
rinses and pauses to remove limescale deposits from inside
the machine.
After about 30 minutes, the water tank is empty, the
(B11)
light comes on and the
,
and
lights alter-
nate. Turn the steam/hot water knob clockwise as far as it will
go to the 0 position.
The appliance is now ready for rinsing through with clean water.
11. Empty the container used to collect the descaler solution
and replace it empty under the cappuccino maker.
12. Remove the water tank, empty, rinse under running water,
fill with clean water and replace. The
,
and
lights flash simultaneously.
13. Turn the steam/hot water knob a half turn anticlockwise to
the
l
position. Hot water comes out of the spout.
14. When the water tank is completely empty, the
light
goes out and the
and
,
,
lights
flash.
15. Turn the knob to the 0 position, fill the water tank again
and the appliance goes off automatically.
To use the appliance, turn it on by pressing the
(B1)
button.
Please note!
If the descaling cycle is not completed correctly (e.g. lack of elec-
tricity) we recommend repeating the cycle.
15. SETTING WATER HARDNESS
The
light (B15) comes on after a period of time estab-
lished according to water hardness.
The machine is set by default for a hardness value of 4 (very hard
water).
The machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
15.1 Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper at-
tached to this manual from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
15.2 Set water hardness
1. Make sure the appliance is off (but connected to the mains
electricity supply and with the main switch (in the
I
posi-
tion) (A2-fig. 3);
2. Press and hold the
button (B14) for at least 6 sec-
onds. The
lights
(B11, B12, B13 and B14) come on simultaneously;
3. Press the ECO button (B16) to set the actual water hardness
(as measured by the indicator paper).
Level Level Level Level
1
2
3
4
4. Press the
button to exit the menu.
The machine is now reprogrammed with the new water hard-
ness setting.
16. TECHNICAL SPECIFICATION
Voltage:
120 V
Absorbed power:
1350 W
Pressure:
1,5 MPa (15 bar)
Water tank capacity:
1,7 L
Size: LxHxD:
280x364x400 mm
Cable length:
1110 mm
Weight:
10,8 kg
level 1
level 2
level 3
level 4
Summary of Contents for ESAM 04.110
Page 1: ...5713212551 06 09 ...
Page 2: ......
Page 4: ...4 4 1 2 3 5 4 6 7 9 8 10 11 13 12 14 15 ...
Page 5: ...5 5 17 16 18 21 20 22 19 ...
