21
No milk froth is formed when
making cappuccino
Model ECP35.31:
the ring is in the “HOT
MILK” position
MODEL ECP35.31:
push the ring into the “CAP-
PUCCINO” position
Milk not cold enough
Always use milk at refrigerator temperature
Cappuccino maker dirty
Clean as described in the section “Cleaning the
cappuccino maker”
Scale in the water circuit
Descale as described in the section “Descaling”
The appliance switches of
Auto-of has been triggered
Press the ON/OFF button to turn the appliance on
again
The appliance switches of a
few seconds after switching on
The mode selector dial is not in the
l
po-
sition (Standby)
Turn the mode selector dial to the
l
position
(Standby), then press the ON/OFF switch.
ELECTRICAL REQUIREMENTS (UK ONLY)
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in
your home, if you are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug,
following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left
where children might find it and plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is
not in use.
IMPORTANT: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
GREEN AND YELLOW
EARTH
BLUE
NEUTRAL
BROWN LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
-
The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth
symbol
or coloured green or green and yellow.
-
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
-
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten
the mains lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in
doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified
electrician and should only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be
used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured
insert in the base of the fuse recess or elsewhere on the plug. Always state this colour when ordering a replacement
fuse cover. Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
Green and Yellow to Earth
13 amp
Fuse
Brown to
live
Cord Clamp
Blue to
neutral
Summary of Contents for ECP31.21
Page 3: ...3 A1 A3 A4 A5 A A6 A17 A14 A15 A15 A16 A8 A7 A9 A10 A8 A9 A11 A2 A12 A13...
Page 4: ...4 1 2 3 5 6 7 8 9 11 12 13 14 15 16 MAX 4 2 1 ready 10 ECP35 31...
Page 5: ...5 17 18 19 20 21 22 23 24 25 26 27 5 C max 1 3 HOTMILK...
Page 22: ...De Longhi Appliances via Seitz 47 31100 Treviso Italia www delonghi com 5713227161 05 15...