19
Please note
The filter lasts about two months if the appliance is used nor-
mally. If the coffee machine is left unused with the filter in-
stalled, it will last a maximum of three weeks.
3. To activate the filter, run tap water through the hole in the
filter as shown in the figure until water comes out of the
openings at the side for more than a minute (fig. 42).
43
42
0,5 L
4. Extract the tank from the appliance and fill with water.
5. Insert the filter in the water tank and immerse it complete-
ly for about ten minutes, sloping it and pressing it lightly to
enable the air bubbles to escape (fig. 43).
6. Insert the filter in the filter housing (fig. 44A) and press as
far as it will go.
7. Close the tank with the lid (fig. 44B), then put the tank
back in the machine.
44A
44B
When you install the filter, you must notify the appliance of its
presence.
8. Press the
MENU/ESC
button (B2) to enter the menu;
9. Press or (fig. 9) until “Install filter” is displayed;
10. Press the
OK
button (fig. 3).
11. “Enable?” is displayed.
12. Press the OK button to confirm the selection. “HOT WATER
Press OK” is displayed.
13. Position a container under the hot water spout (min. ca-
pacity: 500 ml).
14. Press the
OK
button to confirm the selection. The appliance
begins hot water delivery and the message “Please wait” is
displayed.
15. After delivery, the appliance is automatically ready to make the
next drink.
The new filter is active. You can now use the appliance.
Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see date
indicator) or when the appliance has not been used for 3 weeks,
you should replace the filter:
1. Extract the tank and exhausted filter;
2. Take the new filter out of its packet and proceed as illus-
trated in points 2-3-4-5-6-7 in the previous section.
3. Position a container with a minimum capacity of 500 ml
under the hot water spout.
4. Press the MENU/ESC button (B2) to enter the menu.
5. Press < or > (fig. 9) until “Replace filter” is displayed.
6. Press the OK button (fig. 3);
7. “Confirm?” is displayed.
8. Press the OK button to confirm the selection;
9. “HOT WATER Press OK” is displayed.
10. Press the OK button to confirm the selection. The appliance
begins hot water delivery and the message “Please wait” is
displayed.
11. After delivery, the appliance is automatically ready to
make the next drink.
The new filter is now active and you can use the coffee machine.
Removing the filter
If you want to use the appliance without the filter, you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Extract the tank, remove the filter and put the tank back in
the machine.
2. Press the
MENU/ESC
button (B2) to enter the menu;
3. Press or (fig. 9) until “Install filter, Enabled” is
displayed;
4. Press the
OK
button
(fig. 3);
5. “Disable?” is displayed;
6. Press the
OK
button to confirm and the
MENU/ESC
button
to exit the menu.
TECHNICAL DATA
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power:
1450W
Pressure:
15 bar
Max. water tank capacity:
2 l
Size LxHxD:
260 x 360 x 460 mm
Cable length:
1,75 m
Weight:
10,9 kg
Coffee beans container capacity:
400 g
Summary of Contents for ECAM44.66X ELETTA
