18
DISPLAYED MESSAGE
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
FILL TANK
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place (fig. 4).
EMPTy GROUNDS CONTAINER
The grounds container (A14) is full.
Empty the grounds container and drip tray, clean and repla-
ce (fig. 23). Important: when removing the drip tray, the
grounds container MUST be emptied, even if it contains few
grounds. If this is not done, when you make the next coffe-
es, the grounds container may fill up more than expected
and clog the machine.
GROUND TOO FINE ADJUST
MILL
The grinding is too fine and the coffee is delivered too slowly
or not at all.
Repeat coffee delivery and turn the grinding adjustment
dial (fig. 8) one click clockwise towards “7” while the coffee
mill is in operation. If after making at least 2 coffees delivery
is still too slow, repeat the correction procedure, turning the
grinding adjustment dial another click until delivery is cor-
rect (see the section “Adjusting the coffee mill” on page 11).
If the problem persists, turn the steam dial to the I position
and let some water run from the cappuccino maker.
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has not been repla-
ced.
Remove the drip tray and insert the grounds container.
ADD PRE-GROUND COFFEE
The “pre-ground coffee” function has been selected without
placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel or deselect the “pre-
ground” function.
DESCALE
The machine must be descaled.
The descaling procedure described in the section “Descaling”
needs to be performed as soon as possible (page 15).
REDUCE COFFEE AMOUNT
Too much coffee has been used.
Select a milder taste or reduce the quantity of pre-ground
coffee.
FILL BEANS CONTAINER
The coffee beans have run out.
Fill the beans container.
The pre-ground coffee funnel is clogged.
Empty the funnel with the help of a brush, as described in
the section “Cleaning the pre-ground coffee funnel” (page
14).
INSERT INFUSER ASSEMBLy
The infuser has not been replaced after cleaning.
Insert the infuser as described in the paragraph “Cleaning
the infuser” (page 14).
INSERT TANK
The tank is not correctly in place.
Insert the tank correctly and press as far as it will go.
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described
in the section “Cleaning” (page 13). If the message is still
displayed after cleaning, contact customer services.
REPLACE FILTER
The water softener filter is exhausted.
Replace the filter or remove it as described in the section
“Water softener filter” (page 16).
TURN DIAL TO CLEAN
Milk has been delivered recently and the tubes inside the
milk container must be cleaned.
Turn the froth adjustment dial to CLEAN.
INSERT WATER SPOUT
The hot water spout is not inserted or is inserted incorrect-
ly.
Insert the water spout (D3) as far as it will go.
WATER CIRCUIT EMPTy FILL
WATER CIRCUIT
alternating with...
HOT WATER PRESS OK
The water circuit is empty.
Press OK to deliver water from the spout until it flows out
normally.
INSERT MILK CONTAINER
The milk container is not inserted correctly.
Insert the milk container (fig. 13) as far as it will go.
Summary of Contents for ECAM22.360
