DeLonghi ECAM22.360, Instructions For Use Manual

Page: 14 / 20

13
Making cappuccino
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the CAPPUCCINO button. “CAPPUCCINO” is displayed,
together with a progress bar which fills gradually as prep-
aration proceeds.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. For drinks with coffee, the
machine automatically makes the coffee after delivering
the milk.
Please note!
• If during delivery you want to stop making milk or coffee,
press the CAPPUCCINO button twice.
• At the end of delivery, to increase the quantity of milk or
coffee in the cup, within 3 seconds, press and hold the
CAPPUCCINO button.
• Do not leave the milk container out of the refrigerator
for long periods. The warmer the milk (5°C is ideal), the
poorer the quality of froth produced.
Making frothed milk only (without coffee)
Proceed as described in the previous paragraph (Making cap-
puccino or macchiato), pressing the CAPPUCCINO button twice
instead of once.
Please note!
If during delivery you want to stop making milk or coffee, press
the CAPPUCCINO button once.
Making milk only (without froth or coffee)
Proceed as described in the previous paragraph (Making
frothed milk only), turning the froth regulator to
position.
CLEANING THE MILK CONTAINER AFTER USE
I mportant! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout. Avoid
contact with splashes of water.
After preparing a cappuccino or milk based drink, the machine
must be cleaned to remove the milk residues. Proceed as fol-
lows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Turn the froth adjustment dial to CLEAN (fig. 33): the op-
eration is shown on the display (fig. 34) and stops auto-
matically.
4. Turn the dial back to one of the froth selections.
5. Remove the milk container and always clean the steam
nozzle with a sponge (fig. 20).
Please note!
• To prepare a number of cappuccinos and milk based
drinks, clean the milk container after you have prepared
the last drink only.
• The milk container can be kept in the refrigerator.
• In some cases, to clean you must wait for the appliance to
heat up.
Programming the quantity of coffee and milk in the
cup for cappuccino or milk
The appliance is set by default to automatically deliver stand-
ard quantities. To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press and hold the CAPPUCCINO button until the message
“PROGRAM MILK Program quantity” is displayed.
3. Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the CAPPUCCINO button again.
5. The appliance stops delivering milk and after a few sec-
onds the coffee is delivered into the cup. “PROGRAM COF-
FEE Program quantity” is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the CAPPUCCINO button. Coffee deliv-
ery stops.
The machine is now reprogrammed with the new milk and cof-
fee quantities.
HOT WATER
Important! Danger of burns.
Never leave the machine unsupervised while hot water is being
delivered. The spout becomes hot during delivery. Hold by the
handle only.
1. Make sure the hot water spout is attached correctly (fig.
4).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the button (fig. 21). “HOT WATER” is displayed,
together with a progress bar which fills gradually as prep-
aration proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically. To interrupt delivery of hot water
manually, press the
button again.