11
5. Press the
OK
icon (B15) to confirm (or
ESC
(B14) to exit without making the change). The lights go off.
The auto-off time is now programmed.
9. ENERGY SAVING
Use this function to enable or disable energy saving. This mode
is active by default, reducing energy consumption while the ma-
chine is on in compliance with current European regulations. To
change the setting, proceed as follows:
1. With the machine off (standby), but the main switch
pressed (A6) (fig. 1);
2. Press and hold the
icon (B9) until the icons on the
touch screen (B) come on.
3. Press the
icon (B13);
4. Press the
icon again to enable/disable the function:
•
function enabled
•
function disabled
5. Press the
OK
icon (B15) to confirm (or
ESC
(B14) to exit without making the change). The lights go off.
The energy saving setting is now programmed.
Please note:
• When in energy saving mode, a few seconds may elapse
before the first coffee is delivered as the machine must
heat up again.
10. BEEP
This function enables or disables the beep. Proceed as follows:
1. With the machine off (standby), but the main switch
pressed (fig. 1);
2. Press and hold the
icon (B9) until the lights on the
touch screen (B) come on.
3. Press the
icon to enable/disable the function:
•
function enabled
•
function disabled
4. Press the
OK
icon (B15) to confirm (or
ESC
(B14) to exit without making the change). The lights go off.
The beep is now programmed.
11. DEFAULT VALUES (RESET)
This function resets all settings (temperature, auto-off, water hard-
ness, energy saving and all quantity settings are reset to the default
values).
1. With the machine off (standby), but the main switch
pressed (fig. 1);
2. Press and hold the
icon (B9) until the lights on the
touch screen (B) come on.
3. Press the
icon (B12). The bean icons (B7) on the touch
screen flash;
4. Press the
OK
icon (B15) to reset the default values
(or
ESC
(B14) to exit without making the change).
The lights go off.
The settings and quantities of the beverages have been reset to
the default values.
12. RINSING
Use this function to deliver hot water from the coffee spouts
(A19) to clean and heat the machine’s internal circuit.
Place a container with a minimum capacity of 3.38 floz/100ml
under the coffee and hot water spouts.
Important! Danger of burns.
Do not leave the machine unattended while hot water is being
delivered.
1) To activate the function, press
OK
(B15);
2) After a few seconds, hot water is delivered from the coffee
spouts, cleaning and heating the machine’s internal circuit.
3) To interrupt the function manually, press
OK
again.
Please note:
• If the machine is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning it is normal to have water collected in the
coffee ground container (A11).
13. MAKING COFFEE
13.1 Adjusting the coffee grinder
The coffee grinder is set by default to prepare coffee correctly
and should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by calibrating
the coffee grinding using the adjusting dial (A5) (fig. 8).
Please note:
The grinding adjustment dial must only be turned when the
coffee grinder is in operation.
If the coffee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coffee, turn
one click anticlockwise towards 1 (do not
turn more than one click at a time other-
wise the coffee could be delivered a drop
at a time).
