background image

27

Electrical  section

6

6

IMPORTANT:  Installation  must  be  carried  out  according  to  the  manufacturer's
instructions.  Incorrect  installation  may  cause  harm  and  damage  to  people,  ani-
mals  or  property,  for  which  the  manufacturer  accepts  no  responsibility.
Before carrying out any work on the electrical section of the appliance, it must
be  disconnected  from  the  mains.
Connection  to  a  good  earth  wiring  system  is  absolutely  essential.
The  manufacturer  accepts  no  responsibility  for  any  inconvenience  caused  by
failure  to  comply  with  this  rule.

DETAILS

Connection  to  the  electric  power  supply  must  be  carried  out  by  a  qualified
technician and following the appropriate safety regulations.

Before  carrying  out  the  connection  to  the  power  supply,  the  voltage  rating  of  the
appliance  (stamped  on  the  appliance  identification  plate)  must  be  checked  for
correspondence to the available mains supply voltage, and the mains electric wiring
should  be  capable  of  handling  the  appliance’s  power  rating  (also  indicated  on  the
identification plate).

Green &
Yellow

Earth

3  amp

fuse

Blue 

Neutral

Brown 

Live

Fig. 6.1

Summary of Contents for DGS 61 ST

































Reviews: