background image

WARNING: Disconnect all power sources before opening the tablet 
cover or panels. After you finish working inside the tablet, replace all 
covers, panels, and screws before connecting to the power source.

CAUTION: To avoid damaging the tablet, ensure that the work surface 
is flat and clean.

CAUTION: To avoid damaging the components and cards, handle 
them by their edges and avoid touching pins and contacts.

CAUTION: You should only perform troubleshooting and repairs as 
authorized or directed by the Dell technical assistance team. Damage 
due to servicing that is not authorized by Dell is not covered by your 
warranty. See the safety instructions that shipped with the product or 
at www.dell.com/regulatory_compliance.

CAUTION: Before touching anything inside your tablet, ground 
yourself by touching an unpainted metal surface. While you work, 
periodically touch an unpainted metal surface to dissipate static 
electricity, which could harm internal components.

CAUTION: When you disconnect a cable, pull on its connector or on 
its pull tab, not on the cable itself. Some cables have connectors with 
locking tabs or thumb-screws that you must disengage before 
disconnecting the cable. When disconnecting cables, keep them 
evenly aligned to avoid bending any connector pins. When connecting 
cables, ensure that the ports and connectors are correctly oriented 
and aligned.

CAUTION: Press and eject any installed card from the media-card 
reader.

Recommended tools

The procedures in this document may require the following tools:

• Phillips screwdriver
• Plastic scribe

8

Summary of Contents for XPS 12
























































Reviews: